IAI GO-2400M-PMCL User Manual page 72

LineInverter_Nand1In2 R/W
LineSource_Line1 R/W
UserOutput0 R/W
UserOutput1 R/W
7. Analog Control
GainRawAnalogAll R/W
GainRawDigitalRedAll R/W
GainRawDigitalBlueAll R/W
GainAuto R/W
BlackLevelRawAll R/W
BlackLevelRawRed R/W
BlackLevelRawBlue R/W
BalanceWhiteAuto R/W
8. LUT Control
LUTValueRed R/W
LUTValueGreen(Mono) R/W
LUTValueBlue R/W
ND1INV2 False/True
LS0 0: Low
1: High
3: FrameTriggerWait
4: FrameActive
5: ExposureActive
6: Fval
7: Lval
8: PulseGenerator0
10:UserOutput0
11:UserOutput1
12: TTL_In1(Std Only)
13: CL_CC1_In
14: Nand0
15: Nand1
USC0 False/True
USC1 False/True
FGA min to 0 to max
PGR min to 0 to max
PGB min to 0 to max
AGC 0: Off
1: Continuous
BL min to 0 to max
BLR1 min to 0 to max
BLB1 min to 0 to max
AWB 0: Off
1: Once
2: Continuous
3: 4600K
4: 5600K
5: 6600K
Else : Off
LUTR Param 1: LUT
index
Param 2:
LUTdata(Min to
Max)
LUTG Param 1: LUT
index
Param
2:LUTdata(Min to
Max)
LUTB Param 1: LUT
index
Param 2:
LUTdata(Min to
Max)
0 1 0
0 15 0
0 1 0
0 1 0
100 1600 100
–4533 28400 0
–4533 28400 0
0 1 0
–133 255 0
–133 255 0
–133 255 0
0 2 0
0 255 γ=1
0 4095 equivalent
value
γ=1
0 255
0 4095 equivalent
value
0 255 γ=1
0 4095 equivalent
value
̶ 72 ̶
GO-2400M-PMCL / GO-2400C-PMCL
ND1INV2=[Param.]<CR><LF> Enable/disable
ND0INV2?<CR><LF> polarity inversion
for the NAND1 In2
input.
LS0=[Param.]<CR><LF> Select the line
LS0?<CR><LF> source signal for
For 12pin TTL out Line1 (12-pin TTL
output).
USC0=[Param.]<CR><LF> Set the User
USC0?<CR><LF> Output0 value.
USC1=[Param.]<CR><LF> Set the User
USC1?<CR><LF> Output1 value.
FGA=[Param.]<CR><LF> Set the gain value.
FGA?<CR><LF>
PGR=[Param.]<CR><LF> Set the red gain
PGR?<CR><LF> value for white
(Color model only) balance control.
PGB=[Param.]<CR><LF> Set the blue gain
PGB?<CR><LF> value for white
(Color model only) balance control.
AGC=[Param.]<CR><LF> Enable/disable
AGC?<CR><LF> gain auto
adjustment.
BL=[Param.]<CR><LF> Set the black level
BL?<CR><LF> value.
BLR1=[Param.]<CR><LF> Set the red gain
BLR1?<CR><LF> value for black
(Color model only) balance control.
BLB1=[Param.]<CR><LF> Set the blue gain
BLB1?<CR><LF> value for black
(Color model only) balance control.
AWB=[Param.]<CR><LF> Set the auto white
AWB?<CR><LF> balance mode.
(Color model only) (Color only)
LUTR=[Param1],[Param2]<CR><LF> Set the LUT value
LUTR?[Param1]<CR><LF> for the red output
(Col o r model onl y ) signal.
(Color only)
LUTG=[Param1],[Param2]<CR><LF> Set the LUT value
LUTG?[Param1]<CR><LF> for the green
output signal. (for
Color)
Set the LUT value
for the image
output signal. (for
Mono)
LUTB=[Param1],[Param2]<CR><LF> Set the LUT value
LUTB?[Param1]<CR><LF> for the blue output
(Col o r model onl y ) signal.
(Color only)