Display The - IAI GO-2400M-PMCL User Manual

GpioNand1 R/W
InputSource1
GpioNand1 R/W
InputSource2
GpioNand0 R/W
InputInvert1
GpioNand1 R/W
InputInvert1
GpioNand0 R/W
InputInvert2
GpioNand1 R/W
InputInvert2
LUTSequenceR R/W
LUTSequenceG R/W
LUTSequenceB R/W
BlemishNum R/O
CameraLinkClock R/O
Frequency
ND1IN1 0: Low
1: High
3: FrameTriggerWait
4: FrameActive
5: ExposureActive
6: Fval
7: Lval
8: PulseGenerator0
10: UserOutput0
11: UserOutput1
12: TTL_In1(Std Only)
13: CL_CC1_In
15: Nand1
ND1IN2 Same as above.
ND0INV1 0: Non-Inv
1: Inv
ND1INV1 Same as above.
ND0INV2 0: Non-Inv
1: Inv
ND1INV2 Same as above.
LUTSR Min to Max
LUTSG Min to Max
LUTSB Min to Max
BNUM Min to Max
CLCF 0= 84.85MHz
1= 74.25MHz
2= 37.12MHz
0 6 0
0 6 0
0 1 0
0 1 0
0 1 0
0 1 0
0 4095 0
0 4095 0
0 4095 0
0 255 0
0 2 0
̶ 89 ̶
GO-2400M-PMCL / GO-2400C-PMCL
ND1IN1=[Param.]<CR><LF> Select the input
ND1IN1?<CR><LF> source signal for
NAND1 In1.
ND1IN2=[Param.]<CR><LF> Select the input
ND1IN2?<CR><LF> source signal for
NAND1 In2.
ND0INV1=[Param.]<CR><LF> Not required.
ND0INV1?<CR><LF> LineInverter_
Nand0In1 exists
on 37th line.
ND1INV1=[Param.]<CR><LF> Not required.
ND1INV1?<CR><LF> LineInverter_
Nand1In1 exists
on 39th line.
ND0INV2=[Param.]<CR><LF> Not required.
ND0INV2?<CR><LF> LineInverter_
Nand0In2 exists
on 38th line.
ND1INV2=[Param.]<CR><LF> Not required.
ND1INV2?<CR><LF> LineInverter_
Nand1In2 exists
on 40th line.
LUTSR=[Param.]<CR><LF> When 256
LUTSR?<CR><LF> commands are
(Color model only) sent in
succession, the
LUT curve is
updated (during
WRITE) or the LUT
curve is loaded
sequentially
(during READ).
(Red signal)
LUTSG=[Param.]<CR><LF> When 256
LUTSG?<CR><LF> commands are
(Color model only) sent in
succession, the
LUT curve is
updated (during
WRITE) or the LUT
curve is loaded
sequentially
(during READ).
(Green signal)
LUTSB=[Param.]<CR><LF> When 256
LUTSB?<CR><LF> commands are
(Color model only) sent in
succession, the
LUT curve is
updated (during
WRITE) or the LUT
curve is loaded
sequentially
(during READ).
(Blue signal)
BNUM?<CR><LF>

Display the

number of
correction
blemishes.
CLCF =[Param.]<CR><LF> Set the Camera
CLCF?<CR><LF> Link clock.