Beta Enduro RR 350 2015 Workshop Manual page 3

3.9.2 ASSEMBLY OF KICKSTART DEVICE
3.10 ELECTRICAL STARTER UNIT AND MAIN GEAR 79
3.10.1 CHECKING ELECTRICAL STARTER DEVICE
ELEMENTS
3.10.2 COUPLING IGNITION AND PRIMARY GEARS TO THE
MOTOR
3.11 OIL PUMPS: CONTROL AND REASSEMBLY
3.11.1 ASSEMBLY OF LOW PRESSURE PUMP
3.11.2 ASSEMBLY OF HIGH-PRESSURE PUMP AND
CONTROL GEAR
3.11.3 CHECKING AND ASSEMBLY OF PRESSURE
CONTROL VALVE
3.11.4 CHECKING AND ASSEMBLY OF OIL PUMPS
CONTROL GEARS
3.11.5 PAPER OIL FILTER INSERTION
3.11.6 CHECKING AND COUPLING COUNTERSHAFT
3.12 CLUTCH UNIT
3.12.1 CHECKING CLUTCH BASKET, ROLLER BEARING
AND INTERNAL CENTRE BEARING
3.12.2 CHECKING CLUTCH DISCS
3.12.3 CHECKING SPRINGS
3.12.4 CHECKING INNER HUB
3.12.5 CHECKING THRUST BEARING DEVICE
3.12.6 ASSEMBLY OF CLUTCH UNIT
3.13 COOLANT PUMP
3.13.1 CHECKING PUMP UNIT AND DISASSEMBLY
3.13.2 ASSEMBLY OF PUMP UNIT
3.14 ASSEMBLY OF COMPLETE CLUTCH COVER
3.15 CHECKING AND COUPLING OF TIMING
CHAIN, FIXED AND MOBILE GUIDES
3.16 IGNITION SYSTEM
3.16.1 CHECKING IGNITION SYSTEM
3.16.2 COUPLING IGNITION SYSTEM TO CRANKCASE 102
3.17 THERMAL UNIT
3.17.1 CHECKING PISTON, PIN BOLT, AND PISTON
RINGS
3.17.2 CHECKING THE CYLINDER
3.17.2.1 ASSEMBLY CLEARANCE
3.17.3 CYLINDER HEAD: DISASSEMBLY AND CHECKING
AUXILIARY DEVICES
3.17.3.1 LUBRICATION JETS AND CENTRING PINS
3.17.3.2 FINGER FOLLOWER/SHAFTS UNIT
3.17.3.3 SHIMS (CALIBRATED DISCS) FOR VALVE PLAY
ADJUSTMENT
3.17.4 CYLINDER HEAD: DISASSEMBLING AND
CHECKING VALVE UNITS
3.17.4.1 SPRINGS
3.17.4.2 VALVE GUIDES, VALVES AND SEATS
3.17.4.3 VALVE STEM SEAL AND LOWER STOP WASHER
3.17.5 CYLINDER HEAD: CHECKING CYLINDER HEAD
BODY
3.17.6 CHECKING CAMSHAFTS
3.17.7 CHECKING CAMSHAFTS SUPPORT
3.17.8 CYLINDER HEAD: INSERTION OF INNER CUP
AND VALVE STEM SEAL
78 3.17.9 CYLINDER HEAD: ASSEMBLY OF VALVE UNIT
3.17.10 CYLINDER HEAD: REPOSITIONING CALIBRATED
DISCS, ASSEMBLY OF FINGER FOLLOWER SHAFTS
AND FINGER FOLLOWERS AND COUPLING THE
SPARK PLUG
79
3.17.11 CYLINDER HEAD: INSERTION OF OIL JETS,
CENTRING PINS AND SPARK PLUG O-RING
80
3.17.12 PISTON: APPLICATION OF PISTON RINGS AND
OIL-SCRAPER RINGS
82
3.17.13 APPLICATION OF PISTON TO CYLINDER
84
3.17.14 APPLICATION OF PISTON-CYLINDER COUPLING
TO CRANKCASE
85
3.17.15 COUPLING HEAD TO CYLINDER
86
3.17.16 COUPLING CAMSHAFTS TO CYLINDER HEAD
AND PHASING
87
3.17.17 VALVE PLAY
88
3.17.18 CHECKING AND COUPLING OF MECHANICAL
TENSIONER TO ENGINE
89
3.17.19 COUPLING CYLINDER HEAD COVER GASKETS
91
AND CYLINDER HEAD COVER
3.18 PINION COUPLING
91
92
3.19 RELEASING CRANKSHAFT
93
93
3.20 COUPLING OIL CAPS
94
3.21 COUPLING GEARSHIFT LEVER
94
97
4 REASSEMBLY OF ENGINE IN THE VEHICLE
97
ENGINE/FRAME TABLE OF TIGHTENING TORQUES
98
RECOMMENDED ENGINE MAINTENANCE
99
RECOMMENDED LUBRICANTS AND LIQUIDS
101
101
102
105
105
107
107
108
108
109
110
111
112
112
114
114
115
116
117
INDEX
118
119
120
121
122
124
126
127
130
132
134
135
135
136
137
138
152
153
154