Table of Contents
Advertisement
The package of the PBX includes three manuals:
1 installation and configuration manual for the service and
1 operation instruction manual for the user.
1 CAPI/TAPI manual (Fax, Internet, data transfer)
This manual describes the installation and configuration of the PBX. It
also includes a short description of the included software and the asso-
ciated options for the configuration of the PBX.
This manual sorts explanations according to certain question types.
In order to get certain information quickly and carefully directed, the
manual will offer you different helps and guide lines:
The table of contents on
page 3
organization of the operating manual.
The index on
page 63
helps you to find text locations for a certain
term.
In the texts you will be referred to other chapters or pictures with the
help of cross references.
The headlines on each page remind you in which chapter you are
at the present. On the left side of the pages the headlines of the
actual chapter will be repeated. On the right side the headlines of
the paragraph will be repeated.
When handling with 230 volt supply voltage and with the units supplied
by this voltage the relevant electric safety regulations must absolutely
be observed.
Please pay attention to the following general safety advice by all
means:
All devices must be installed without current. (e.g. in case of main-
tenance work).
All devices may only be put into operation if they are properly built
into the case.
Units that operate with external voltage - especially with supply volt-
age - may only be opened if they were disconnected from the volt-
age source or from the mains first.
The mains cables of the electric devices and the connection cables
must regularly be checked for damages. If you discover damages,
the concerning cables must be replaced.
PBX Basic Configuration
Power Supply
Operating Voltage
230 V
Nominal current
COMpact 2206 USB: max. 140 mA
COMpact 4410 USB: max. 160 mA
Isolation class
I
Power consumption
COMpact 2206 USB: max. 16 VA
COMpact 4410 USB: max. 25 VA
Instructions for using the Manual
gives you an idea of content and
General Safety Advice
Technical Data
10%, 50 Hz
Abbreviations used in this Manual
DDI
Direct Dialling In number in case of a PTP connection
(Direct Dialling In)
MSN
Multiple Subscriber Number in case of a PTMP connection
(Multiple Subscriber Number)
NT
Network termination unit for the basic connection (Network
Termination)
CF
Call forwarding
Symbols used in the manual
The danger sign shows you an important advice. You
e
must absolutely take care of these in order to avoid dam-
ages to devices or even to persons.
The hand gives you additional advice. These refer you to
circumstances that were often disregarded and therefore
led to misunderstandings and longer search for an error.
LED flashes.
LED is on.
The use of tools near or on covered or open circuit lines and circuit
boards as well as on and in devices that are supplied with external
power - especially with mains voltage - must be avoided as long as
the supply voltage is not switched off and the device is not made
free of voltage by discharging existing capacitors. The charge
capacitor of the switching power supply unit can be charged for a
long time in case of a failure even after being switched off.
If you use construction elements, components, assembly groups,
connections and units, you must absolutely take care of the limita-
tion values for voltage, currency and power consumption indicated
in the technical data. Exceeding those limitation values (also short-
time) may cause extensive damages.
The units, unit assemblies or connections mentioned in this opera-
tion instructions may only be used as described. If you are not sure
how to use the merchandise, please ask a specialist.
Temperature Range
Operational
+0...+40 Degree Celsius, Protect against direct sunlight!
Storage and Transport
-20...+70 Degree Celsius
Humidity
10 - 75%, non condensing
External Connections
Usage
1 S
port external
0
Connector Type
Western modular jack RJ-45
Connection Type, external
S
basic rate connection as Point-to-Multipoint or Point-
0
to-Point connection, Euro-ISDN (DSS-1), PBX is self
powered
Termination Resistors
not available
9
Introduction
Hide quick links:
Advertisement
Table of Contents
