Table of Contents
Advertisement
38
Call Distribution
Numbering plan internal; is created when the first operation
starts
(chapter Initialize Telephone Settings on page
depending on the modules in use.
Call distribution external (external call, ringing):
Serial port:
Immediate exchange dial tone copy:
Special dial tone call data memory/filling level
Special dial tone Do-not-Disturb, Baby Call, CF:
Blocking numbers, release numbers:
Door key call distribution:
Door key signalling:
Door key inputs:
Door opener authorization:
Moving function for ISDN/change of port:
Delay time for delayed external ringing:
Delay time for delayed call forwarding
Preferred exchange line (preferred external S
Dial tone, internal:
Wake-up time:
In order to be reachable from internal or external telephones, the indi-
vidual subscribers must get internal telephone numbers and be entered
into the external call distribution (external call ringing, see also
Creating a Basic Configuration on page
Assign internal Telephone Numbers
The PBX allows the free assignment of internal telephone numbers to
internal subscribers, groups etc. These must be entered under internal
telephone numbers in COMset. At your disposal are the 2-digit tele-
phone numbers from 10 to 59 as well as the 3-digit telephone numbers
100 - 599.
The use of 2-digit telephone numbers restricts automatically the availa-
bility of 3-digit telephone numbers. If e.g. the telephone number 12 was
given away, the telephone numbers 120-129 would not longer be avai-
lable.
You can connect the numbers in the emergency Short-Code Dial mem-
ory to these numbers. The advantage is that even persons without PBX
experience or knowledge of exchange line access numbers can dial
these numbers without any problems (e.g. 110). In the default factory
settings such a connection has already been made for the telephone
numbers 110 and 112. So these telephone numbers will not be availa-
ble any longer for assignment.
analog subscribers: internal telephone numbers 30-35 (30-39)
57)
S
2: internal telephone numbers 41, 42, 43.
0
S
3: internal telephone numbers 21, 22 (COMpact 4410 USB only).
0
S
4: internal telephone numbers 25, 26 (COMpact 4410 USB only).
0
USB port (ISDN PC-controller): internal telephone numbers 54, 55, 56, 57
Groups: internal telephone numbers 201-208 and 401-408
Call to system display: internal telephone number 50 (The first analog subscriber
is assigned to the system display as user. Referring to this telephone numbering
plan this is the subscriber 30.)
Door 1: internal telephone number 51
Door 2: internal telephone number 52 (COMpact 4410 USB only)
Audio Out: internal telephone number 53
Short-Code Dial memory 8110: internal telephone number 110 (entry 110)
Short-Code Dial memory 8112: internal telephone number 112 (entry 112)
no preset
no special function
deactivated
deactivated/80 %
activated
no entry, deactivated
the first analog subscriber 30 rings on each door bell
deactivated
all inputs for door key, switchable with 5 - 15 V AC/DC
activated
activated
20 seconds
20 seconds
port):
1st external S
0
3 x short for all subscribers
no entries, deactivated
Call Distribution
chapter
15).
port
0
External Call Distribution (External Call Ringing)
To reach internal subscribers from the exchange line, the telephone
numbers available on the ISDN connections have to be registered as
exchange line numbers in COMset first (up to 100 telephone numbers
can be managed) and have to be distributed to the internal subscribers
and groups under Call Distribution. The configuration of a delayed
external call ringing is also possible. The External call ringing delay
time can also be changed in COMset.
Callers dialling a wrong DDI (existing on the basic rate connection but
not configured in COMset) or an incomplete DDI, will be switched to the
first entered DDI of the corresponding exchange line after 4 seconds.
Call Waiting
Each user can switch on/off „knocking" on his unit if necessary
in the user
manual). With COMset the activation can depend on some
Call Waiting conditions for individual subscribers. So e.g. the „knock-
ing" can be permitted in case that the corresponding subscriber is
allowed to take the call without hanging up the receiver and/or in case
that no other telephone rings with the same telephone number.
(page 24
Hide quick links:
Advertisement
Table of Contents
