Mazda 626 1989 Workshop Manual page 143

Item
Ulearance
OI p is iu n u n y iu n n y
yiuuvc
Piston pin
Diameter
Interference in connecting rod
^Piston to piston pin clearance
Installtion pressure
Connecting rod and connecting rod bearing
Length (Center to center)
Twisting
Bending
Small end bore
Big end bore
Big end width
Connecting rod side clearance
Crankshaft
Crankshaft runout
Main journal diameter
mm (in)
Main journal taper and out-of-round
Crank pin diameter mm (in)
Crank pin taper and out-of-round mm (in)
Main bearing
Main journal bearing oil
clearance mm (in)
Available undersize bearing
Crank pin bearing
un uiecuanue
p in u e a in iy
Available undersize bearing
Thrust bearing (center main bearing)
Crankshaft end play
Bearing width mm (in)
Timing belt
Belt deflection
Engine model
Top
Second
Maximum
mm (in)
mm (in)
mm (in)
N (kg, lb)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
Standard
mm (in)
Maximum
mm (in) Maximum
Standard size
Standard
0.25 (0.010)
undersize
No. 3
No. 1,2,4,5
0.50 (0.020)
undersize
No. 3
0.75 (0.030) No. 1,2,4,5
undersize
No. 3
mm (in) Maximum
Standard
0.25 (0.010) undersize
0.50 (0.020) undersize
0.75 (0.030) undersize
Maximum
Standard
No. 1,2,4,5
Maximum
Standard
No. 3
Maximum
mm (in)
Standard
mini ^iii;
Maximum
mm (in)
Standard
mm (in)
Maximum
Standard
0.25 (0.010) oversize
0.50 (0.020) oversize
0.75 (0.030) oversize
mm (in)/98 N (10 kg, 22 lb)
F2
Turbo
0.03—0.07 (0.0012—0.0028)
0 .0 3 -0 .0 7 (0.0 012-0.0 028)
0.15 (0.006)
2 1 .9 7 4 -2 1 .9 8 0 (0 .86 51-0.8 65 4)
0 .0 1 3 -0 .0 3 7 (0.0005—0.0015)
0 .0 0 8 -0 .0 2 4 (0 .00 03-0.0 0 09)
4,900— 14,700 (5 0 0 --1,500, 1,100—3,300)
158.45— 158.55 (6.238—6.242)
0.57 (0.0224) max.
0.24 (0.0094) max.
21.943—21.961 (0.86 4 0-0 .8646 )
54.002—54.017 (2.1261—2.1266)
2 6 .8 3 8 -2 6 .8 9 0 (1.0 5 6 6 -1 .0 5 8 7 )
0 .1 1 0 -0 .2 6 2 (0 .0 0 4 -0 .0 1 0 )
0.30 (0.012)
0.03 (0.0012)
5 9 .9 3 7 -5 9 .9 5 5 (2.3 5 9 7 -2 .3 6 0 4 )
5 9 .6 9 3 -5 9 .7 1 1 (2 .3 0 5 1 -2 .3 5 0 8 )
59.687—59.705 (2.3499—2.3506)
59.443—59.461 (2 .3403 -2 .3 410 )
59.437—59.455 (2.3400—2.3407)
59.193—59.211 (2.3304—2.3311)
59.187—59.205 (2.3302—2.3309)
0.05 (0.0020)
50.940—50,955 (2.0055—2.0061)
5 0 .6 9 0 -5 0 .7 0 5 (1.9 9 5 7 -1 .9 9 6 3 )
50.440—50.455 (1.9858— 1.9864)
5 0 .1 9 0 -5 0 .2 0 5 (1 .9760 -1 .9 766 )
0.05 (0.0020)
0 .0 2 5 -0 .0 4 3 (0 .0 0 1 0 -0 .0 0 1 7 )
0.08 (0.0031)
0.031—0.049 (0.0012—0.0019)
0.08 (0.0031)
0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
0.027—0.067 (0.0011—0.0026)
0.10(0.0039)
0.25 (0.010), 0.50 (0.020), 0.75 (0.030)
0.08—0.18 (0.0031—0.0071)
0.30 (0.0118)
27.94—27.99 (1.100— 1.102)
2 8 .0 4 -2 8 .0 9 (1 .1 0 4 -1 .1 0 6 )
28.12— 28.17 (1 .1 0 7 -1 .1 0 9 )
2 8 .2 0 -2 8 .2 5 (1 .1 1 0 -1 .1 1 2 )
8.0—9.0 (0 .3 1 -0 .3 5 )
Non-Turbo
^