Mazda 626 1989 Workshop Manual page 134

30
TECHNICAL DATA
Item
• . . .
Ring groove width in piston
C le a r a n c e o r p is io q , rin g
io
Piston pin
Diameter
Interference in connecting rod
Piston to piston pin clearance
Installation pressure
Connecting rod and connecting rod bearing
Length (Center to center)
Twisting
Bending
Snlall end bore
Big end bore
Big end width
Connecting rod side clearance
Crankshaft
Crankshaft runout
Main journal diameter
mm (in)
' Main journal taper and out-of-round mm (in)
Crankpin diameter
mm (in)
Crankpin taper and out-ofaound
Main bearing
Main journal bearing oil
clearance mm (in)
Available undersize bearing
Crankpin bearinq
u r a n K p in o e a r in g on c le a r a n c e
Available undersize bearing
Thrust bearinq (center main bearinq)
Crankshaft end play
Bearing width mm (in)
Engine model
Top
Second
i\.
Oil (rail)
Maximum
Top
mm (in)
Second
Oil
Top
rin g
Second
Maximum
mm (in)
mm (in)
mm (in)
N (kg, lb)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
Standard
mm (in)
Maximum
mm (in)
Maximum
Standard size
Standard
0.25 (0.010)
undersize
No.3
No. 1,2,4,5
0.50 (0.020)
undersize
No. 3
No. 1,2,4,5
0.75 (0.030)
undersize
No. 3
Maximum
Standard
0.25 (0.010) undersize
0.50 (0.020) undersize
0.75 (0.030) undersize
mm (in) Maximum
Standard
No. 1,2,4,5
Maximum
Standard
No. 3
Maximum
mm (in)
Standard
m m ^ n j
Maximum
mm (in)
Standard
mm (in)
Maximum
Standard
0.25 (0.010) oversize
0.50 (0.020) oversize
0.75 (0.030) oversize
FE 12-valve
0.20— 0.35 (0.008—0.0138)
0 .1 5 - 0 .3 0 (0 .0 0 6 -0 .0 1 2 )
0.20—0.70 (0 .0 0 8 -0 .0 2 7 6 )
1.0 (0.039)
1.52— 1.54 (0 .0 5 9 8 -0 .0 6 0 6 )
1 .5 2 -1 .5 4 (0 .0 5 9 8 -0 .0 6 0 6 )
4.02—4.04 (0.1583—0.1591)
0.03—0.07 (0 .0 0 1 2 -0 .0 0 2 8 )
0.03—0.07 (0.0012—0.0028)
0.15 (0.006)
21.974—21.980 (0.8651— 0.8654)
0.013— 0.037 (0.0005— 0,0015)
0.008— 0.024 (0.0003—0.0009)
4,900— 14,700 (500— 1,500, 1,100—3,300)
151.95— 152.05 (5.982—5.986)
0.57 (0.0224) max.
0.24 (0.0094) max.
21.943— 21.961 (0.8640—0.8646)
54.002— 54.017 (2 .1 2 6 1 -2 .1 2 6 6 )
26.838— 26.890 (1.0566— 1.0587)
0 .1 1 0 -0 .2 6 2 (0 .0 0 4 -0 .0 1 0 )
0.30(0.012)
0.03 (0.0012)
59.937—59.955 (2.3 5 9 7 -2 .3 6 0 4 )
5 9 .6 9 3 -5 9 .7 1 1 (2.3501—2.3508)
59.687— 59.705 (2.3499—2.3506)
59.443—59.461 (2.3403—2.3410)
59.437— 59.455 (2 .3 4 0 0 -2 .3 4 0 7 )
59.193— 59.211 (2.3304— 2.3311)
59.187— 59.205 (2 .3 3 0 2 -2 .3 3 0 9 )
0.05 (0.0020)
50.940— 50.955 (2 .0 0 5 5 -2 .0 0 6 1 )
50.690— 50.705 (1 .9 9 5 7 -1 .9 9 6 3 )
50.440— 50.455 (1.9858— 1.9864)
5 0 .1 9 0 -5 0 .2 0 5 (1.9760— 1.9766)
0.05 (0.0020)
0.025—0.043 (0 .0 0 1 0 -0 .0 0 1 7 )
0.08 (0.0031)
0.031—0.049 (0.0012—0.0019)
0.08 (0.0031)
0.25 (0.010). 0.50 (0.020), 0.75 (0.030)
0.027—0.067 (0.0011 —0.00261
0.10 (0.0039)
0.25 (0.010). 0.50 (0.020V 0.75 (0.030)
0.08— 0.18 (0 .0 0 3 1 -0 .0 0 7 1 )
0,30 (0.011 8)
27.94—27.99 (1.100— 1.102)
28.04— 28.09 ( 1 \ 0 4 — 1.106)
28.12—28.17(1.1 O'?— 1.109)
28.20—28.25 (1.110— 1.112)
~~~~
__
___
_____
_ _
_ _
____