Mazda 626 1989 Workshop Manual page 142

30
TECHNICAL DATA
—-
~~~~~~~~~-------
Item
Vaive spring
Free length mm (in)
Out-of-square
Setting load/height N (kg, lb)/mm (in)
Camshaft
Camlobe height mm (in)
Journal diameter mm (in)
Camshaft bearing oil
clearance mm (in)
Camshaft runout
Camshaft end play
Rocker arm and rocker arm shaft
Rocker arm inner diameter
Rocker arm shaft diameter
Rocker to shaft clearance
arm
Cylinder block
Height
Distortion
Grinding limit
Cylinder bore diameter
mm (in)
Cylinder bore taper and out-of-round
Piston
Piston diameter measured
at 90° to pin bore axis
and 18.0 mm (0.709 in)
below oil ring groove
mm (in)
Piston and cylinder clearance
Piston ring
Thickness
End gap measured in cylinder
Ring groove width in piston
Engi ne model
- - — ___
Standard
IN
Minimum
Standard
EX
Minimum
(in) Maximum
m m
IN
EX
Standard
IN
Minimum
Standard
EX
Minimum
Front and Rear (No. 1,5)
Center (No. 2,3,4)
Maximum
Out-of-round
Front and Rear (No. 1,5)
Center (No. 2,3,4)
Maximum
mm (in) Maximum
Standard
mm (in)
Maximum
mm (in)
mm (in)
Standard
mm (in)
Maximum
mm (in)
mm (in) Maximum
mm (in)
Standard
0.25 (0.010) oversize
0.50 (0.020) oversize
mm (in) Maximum
Standard
0.25 (0.010) oversize
0.50 (0.020) oversize
Standard
mm (in)
Maximum
Top
mm (in)
Second
Top
Second
mm (in)
Oil (rail)
Maximum
Top
mm (in) Second
Oil
F2
Turbo
49.5 (1.949)
48,3 (1.902)
50.4 (1.984)
----------------- 49,24-1J33Z)
1.7 (0.067)
2 0 3 - 2 3 0 (20.7—23.4, 4 5 .5 - 5 1 .5)/41 (1.614)
2 4 0 -2 7 2 (2 4 .5 -2 7 .7 , 5 3 .9 -6 0 .9 )/4 1 (1.614)
41.290—41.390 (1.6256— 1.6295)
41.140(1.6197)
4 1 .7 9 7 -4 1 .8 9 7 (1 .6 4 5 5 -1 .6 4 9 5 )
41.647 (1.6396)
3 1 .9 4 0 -3 1 .9 6 5 (1 .2 5 7 5 -1 .2 5 8 5 )
3 1 .9 1 0 -3 1 .9 3 5 (1.2563— 1.2573)
0.05 (0.002)
0 .0 3 5 -0 .0 8 5 (0 .0 0 1 4 -0 .0 0 3 3 )
0 .0 6 5 -0 .1 1 5 (0 .0 0 2 6 -0 .0 0 4 5 )
0.15 (0.0059)
0.03 (0.0012)
0.08—0.16 (0.003—0.006)
0.20 (0.008)
1 9 .0 0 0 -1 9 .0 3 3 (0 .7 4 8 -0 .7 4 9 )
18.959— 18.980 (0 .7 4 6 -0 .7 4 7 )
0.020—0.074 (0.0008—0.0029)
0.10 (0.004)
301.5(11.87)
0.15 (0.006)
0.20 (0.008)
86.000—86.019 (3.3858—3.3866)
86.250—86.269 (3.3957— 3.3964)
8 6 .5 0 0 -8 6 .5 1 9 (3.4055— 3.4062)
0.019 (0.0007)
85.944—85.964 (3.3836— 3.3844)
86.194—86.214 (3.3935—3.3942)
86.444—86.464 (3.4033— 3.4041)
0 .0 3 6 -0 .0 7 5 (0.0014—0.0030)
0.15 (0.0059)
1.47— 1.49 (0.0579—0.05871
1.47— 1.49 (0.0579— 0.0587)
0 .2 0 -0 .3 5 (0.008—0.0138)
0.15—0.30 (0.006—0.0121
0.20—0.70 (0.008-0.02761
1.0 (0.039)
1.52— 1.54 (0.0598—0.0606)
1 .5 2 -1 ,5 4 (0.0598— 0.06061
4.02—4 0 4 (0 .1 5 8 3 —0.15911
Non-Turbo
~~~
'
__
_
_