Table of Contents
Advertisement
®
eXtendo
Emulation Command Set Reference
2.1.21
ESC [F0]+[06]+[x]+[n]+[m] End of page
[Name]
End of page
[Function]
This command signals the end of page, prints the buffer, initiates cutting (if
desired), and allows the transmission of a parameter byte to be echoed back by
the printer after printing is completed
16
[Code]
[1B]
10
[27]
[Description]
1.
The "ESC [F0] + [06] + [x] + [n] + [m]" command signals the end of page, prints the buffer,
initiates cutting (if desired), and allows the transmission of a parameter byte to be echoes back by
the printer after printing is completed.
2.
Permissible values of [x] are "1" and "2".
If x = 1, then the command is to be used without a parameter byte to be echoed back. In this
case, the syntax is [1B]
If x = 2, then the command is to be used with a parameter byte. The syntax then is
16
16
16
[1B]
+ [F0]
+ [06]
3.
Parameter [n] is broken into a most significant nybble (MSN) and a least significant nybble (LSN).
The LSN controls cutting, as follows, and has the permissible values of "0", "1" or "2".
If LSN[n] = 0, no cut will occur after printing.
If LSN[n] = 1, a partial cut will occur after printing (if available).
If LSN[n] = 2, a full cut will occur after printing (if available).
The MSN of n determines whether the command is interpreted as an "End of Print" or an "End of
Form".
If MSN [n] = 0, the command is treated as an "End of Print".
If MSN [n] = 1, the command is treated as an "End of Form".
4.
"End of Print" acts as follows. (Please note that the "End of Print" command generally causes
immediate movement of the paper and execution of the cut, as commanded. Also please note
that anytime the "Top of Page" is set, the "Top of Form" is also set to the same location. When
the "Top of Form" is set directly, it has no impact on the "Top of Page" location.)
If End of Print is sent with no cut command, the current location will be set as "Top of Page".
If End of Print is sent with a partial cut command, this location will be set as "Top of Page", the
paper will be advanced to the cut line, and a partial cut will occur. There will be no retracting to
the park position because the partially cut paper is still attached to the paper roll.
If End of Print is sent with a full cut command, this location will be set as "Top of Page", the paper
will be advanced to the cut line, and a full cut will occur. The paper will then be retracted to the
park position.
5.
"End of Form" acts as follows. (Please note that the "End of Form" command generally causes
no movement of the paper.)
If End of Form is sent with no cut command, the current location will be set as "Top of Form".
If End of Form is sent with a partial cut command, this location will be set as "Top of Form" and a
partial cut will occur when this location moves under the cut line due to other printing commands
(additional data printed, line feeds, etc.).
If End of Form is sent with a full cut command, this location will be set as "Top of Page", and a full
cut will occur when this location moves under the cut line due to other printing commands
(additional data printed, line feeds, etc.).
6.
The default value for [n] is "0".
7.
Permissible values for [m] are in the range [0]
Part No. D 684 112
16
16
+ [F0]
+ [06]
+ [x] + [n] + [m]
10
10
+ [240]
+ [06]
+ [x] + [n] + [m]
16
16
16
+ [F0]
+ [06]
+ [01] + [n].
+ [02] + [n] + [m].
Mod.Nr. 4 150813 LEV
10
10
<= [m] <= [255]
.
Page 31 of 95
- Quick Links:
- 2.1 Emulation Command Set
Hide quick links:
Advertisement
Table of Contents
