Table of Contents
Advertisement
xStack® DGS-3620 Series Managed Switch Web UI Reference Guide
swUnitRemove
swUnitFailure
swUnitTPChange
swUnitRoleChange
vrrpTrapNewMaster
VRRP
vrrpTrapAuthFailure
swL2PortSecurityViolationTrap
Port Security
swSafeGuardChgToNormal
Safe Guard
swSafeGuardChgToExhausted
swPortLoopOccurred
LBD
swPortLoopRestart
swVlanLoopOccurred
swVlanLoopRestart
swBpduProtectionUnderAttackingTrap When the BPDU Protection trap is enabled, if
BPDU Attack
Protection
(1) swUnitMgmtId.
(2) swUnitMgmtMacAddr.
Unit Hot Remove notification.
Binding objects:
(1) swUnitMgmtId.
(2) swUnitMgmtMacAddr.
Unit Failure notification.
Binding objects:
(1) swUnitMgmtId.
The stacking topology change notification.
Binding objects:
(1) swStackTopologyType
(2) swUnitMgmtId
(3) swUnitMgmtMacAddr
The stacking unit role change notification.
Binding objects:
(1) swStackRoleType
(2) swUnitMgmtId
The newMaster trap indicates that the sending
agent has transitioned to 'Master' state.
Binding objects:
(1) vrrpOperMasterIpAddr
A vrrpAuthFailure trap signifies that a packet has
been received from a router whose
authentication key or authentication type
conflicts with this router's authentication key or
authentication type. Implementation of this trap
is optional.
Binding objects:
(1) vrrpTrapPacketSrc
(2) vrrpTrapAuthErrorType
When the port security trap is enabled, new
MAC addresses that violate the pre-defined
port security configuration will trigger trap
messages to be sent out.
Binding objects:
(1)swPortSecPortIndex
(2)swL2PortSecurityViolationMac
This trap indicates system change operation
mode from axhausted to normal.
Binding objects:
(1) swSafeGuardCurrentStatus
This trap indicates System change operation
mode from normal to exhausted.
Binding objects:
(1) swSafeGuardCurrentStatus
The trap is sent when a port loop occurs.
Binding objects:
(1) swLoopDetectPortIndex
The trap is sent when a port loop restarts after
the interval time.
Binding objects:
(1) swLoopDetectPortIndex
The trap is sent when a port loop occurs under
LBD VLAN-based mode.
Binding objects:
(1) swLoopDetectPortIndex
(2) swVlanLoopDetectVID
The trap is sent when a port loop restarts under
LBD VLAN-based mode after the interval time.
Binding objects:
(1) swLoopDetectPortIndex
(2) swVlanLoopDetectVID
the specific port changes from a normal state to
490
1.3.6.1.4.1.171.12.11.2.2.1.
0.2
1.3.6.1.4.1.171.12.11.2.2.1.
0.3
1.3.6.1.4.1.171.12.11.2.2.1.
0.4
1.3.6.1.4.1.171.12.11.2.2.1.
0.5
1.3.6.1.2.1.68.0.1
1.3.6.1.2.1.68.0.2
1.3.6.1.4.1.171.11.118.X.2.
100.1.2.0.2
(X: model ID)
1.3.6.1.4.1.171.12.19.4.1.0.
2
1.3.6.1.4.1.171.12.19.4.1.0.
1
1.3.6.1.4.1.171.12.41.10.0.
1
1.3.6.1.4.1.171.12.41.10.0.
2
1.3.6.1.4.1.171.12.41.10.0.
3
1.3.6.1.4.1.171.12.41.10.0.
4
1.3.6.1.4.1.171.12.76.4.0.1
Advertisement
Table of Contents
