Table of Contents
Advertisement
FIFO Interrupt Trigger Level bits 11-10, C-39
Overrun bit 11-7, C-36
Ready Interrupt Enable bit 11-10, C-39
Ready Interrupt flag 11-14, C-43
Register Select field 16-7, C-46
Request to send 4-8, 11-2
Reset 4-4
block diagram 9-2
out 4-5
pins 9-2
sequence 9-3
Source/Chip Configuration Register 9-3, C-6
sources 9-2
timing specifications A-2
Return
from Exception 2-3
from Fast Interrupt 2-3
RFI instruction 2-3
RISC 2-1
RLD bit 9-12, 9-13, 9-15, C-12
ROM module 5-1
Row senses 4-7
RRDY bit 11-14, C-43
RRDYEN bit 11-10, C-39
RS field 16-7, C-46
RSCR 9-3, C-6
RST bit 9-4, C-6
RSTIN signal 4-4, 9-4, C-6
RSTOUT signal 4-5
RTE instruction 2-3
RTS Delta bit 11-15, C-43
RTS Delta Interrupt Enable bit 11-11, C-39
RTS Pin Status bit 11-14, C-43
RTS signal 11-2
RTS0 4-8
RTSD bit 11-15, C-43
RTSD EN bit 11-11, C-39
RTSS bit 11-14, C-43
Run mode 8-4
RX DATA bits 11-8, C-37
Rx DATA register 12-5, C-30
RxD signals 4-7, 11-3
RXEN bit 11-10, C-39
RxFL bit 11-10, C-39
–S–
S bit 2-3
Scratch registers 2-3, 2-4
Send Break bit 11-11, C-40
Sequential Breakpoint A, B Arm Occurrence bits 16-12,
C-51
Sequential Control field 16-9, C-48
Serial protocol, OnCE 16-21
Shadow registers 2-3, 2-4
SHEN bits 7-7, 7-12, C-22
Show Cycle Enable bits 7-7, 7-12, C-22
Signals 4-1
edge port 13-1
EIM 7-1
MOTOROLA
I-6
All manuals and user guides at all-guides.com
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
ISPI 12-3
KPP 14-2
M•CORE bus 2-9
OnCE 16-3
UART 11-2
Slave mode 12-3, 12-10
SNDBRK bit 11-11, C-40
SNS bit 12-6, C-31
Software Debug Occurrence bit 16-11, C-50
SP bit 7-6, 7-10, C-19
SPCR 12-5, C-31
SPDR 12-5, C-30
SPI
data master in/slave out 4-8
data master out/slave in 4-8
enable 4-8
general-purpose output 4-8
serial clock 4-8
SPI_CLK signal 4-8, 12-4
SPI_EN bit 12-6, C-31
SPI_EN Sense bit 12-6, C-31
SPI_EN signal 4-8, 12-4
SPI_GP Control bit 12-7, C-32
SPI_GP signal 4-8, 12-4
SPI_MISO signal 4-8, 12-3
SPI_MOSI signal 4-8, 12-4
SPICR 12-8, C-33
SPIGP bit 12-7, C-32
SPRAM bit 7-12, C-21
SPROM bit 7-12, C-21
SPSR 12-8, C-34
SQA bit 16-12, C-51
SQB bit 16-11, C-50
SQC field 16-9, C-48
SRAM 6-1
Stack pointer 2-3, 2-6
Standby battery power 4-9
Standby mode 8-6
Standby power filter 4-9
Start bit 11-4
Static RAM 6-1
Status registers 2-3
Stop bit 11-4
STOP bit (PIT) 9-14, C-11
Stop bits 11-13, C-41
Stop mode 8-4
STPB bit 11-13, C-41
Subroutine calls 2-3
Supervisor mode 2-3
Supervisor Protect bit 7-6, 7-10, C-19
SWO bit 16-11, C-50
SZ field 16-19, C-52
–T–
TAP 16-1
TC field 16-19, C-53
TCK 4-5
TCK signal 16-3
TDI signal 4-5, 16-3
MMC2001
REFERENCE MANUAL
Advertisement
Table of Contents
