H4: Analog Outputs - YASKAWA GA800 Maintenance & Troubleshooting

3.10 H: Terminal Functions
Setting Value Function
13 Torque Reference / Torque
Limit
14 Torque Compensation
15 General Torque Limit
16 Differential PID Feedback
1F Not Used
30 DWEZ Analog Input 1
31 DWEZ Analog Input 2
32 DWEZ Analog Input 3
◆

H4: Analog Outputs

No.
Name
(Hex.)
H4-01 Terminal FM Analog Output
Select
(041D)
H4-02 Terminal FM Analog Output
Gain
(041E)
RUN
H4-03 Terminal FM Analog Output
Bias
(041F)
RUN
H4-04 Terminal AM Analog Output
Select
(0420)
H4-05 Terminal AM Analog Output
Gain
(0421)
RUN
H4-06 Terminal AM Analog Output
Bias
(0422)
RUN
H4-07 Terminal FM Signal Level
Select
(0423)
220
V/f CL-V/f OLV CLV AOLV
Enters the torque reference if the motor rated torque is 100%. This setting is the torque limit for speed control.
V/f CL-V/f OLV CLV AOLV
Enters the torque compensation value if the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the torque limit that is the same for all quadrants for forward, reverse, and regenerative operation if the motor rated torque is
100%.
V/f CL-V/f OLV CLV AOLV
Enters the PID differential feedback value if the full scale analog signal (10 V or 20 mA) is 100%.
V/f CL-V/f OLV CLV AOLV
Use this setting for unused terminals or to use terminals in through mode.
V/f CL-V/f OLV CLV AOLV
Use with DriveWorksEZ. Refer to the DriveWorksEZ online manual for more information.
V/f CL-V/f OLV CLV AOLV
Use with DriveWorksEZ. Refer to the DriveWorksEZ online manual for more information.
V/f CL-V/f OLV CLV AOLV
Use with DriveWorksEZ. Refer to the DriveWorksEZ online manual for more information.
V/f CL-V/f OLV CLV AOLV
Sets the monitor number to send from MFAO terminal FM.
Set the x-xx part of the Ux-xx [Monitor]. For example, set H4-01 = 102 to monitor U1-02 [Output
Frequency].
V/f CL-V/f OLV CLV AOLV
Sets the gain of the monitor signal that is sent from MFAO terminal FM.
Sets the analog signal output level from the terminal FM at 10 V or 20 mA as 100% when an output
for monitoring items is 100%.
V/f CL-V/f OLV CLV AOLV
Sets the bias of the monitor signal that is sent from MFAO terminal FM.
Set the level of the analog signal sent from terminal FM at 10 V or 20 mA as 100% when an output
for monitoring items is 0%.
V/f CL-V/f OLV CLV AOLV
Sets the monitoring number to be output from the MFAO terminal AM.
Set the x-xx part of the Ux-xx [Monitor]. For example, set H4-04 = 103 to monitor U1-03 [Output
Current].
V/f CL-V/f OLV CLV AOLV
Sets the gain of the monitor signal that is sent from MFAO terminal AM.
When an output for monitoring items is 0%, this parameter sets the analog signal output level from
the AM terminal at 10 V or 20 mA as 100%.
V/f CL-V/f OLV CLV AOLV
Sets the bias of the monitor signal that is sent from MFAO terminal AM.
When an output for monitoring items is 0%, this parameter sets the analog signal output level from
the AM terminal at 10 V or 20 mA as 0%.
V/f CL-V/f OLV CLV AOLV
Sets the MFAO terminal FM output signal level.
Note:
Set jumper S5 on the control circuit terminal block accordingly when changing these parameters.
0 : 0-10V (Lower Limit at 0)
1 : -10 to +10V (Bipolar Reference)
2 : 4 to 20 mA
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
Default
(Range)
102
(000 - 999)
100.0%
(-999.9 - +999.9%)
0.0%
(-999.9 - +999.9%)
103
(000 - 999)
50.0%
(-999.9 - +999.9%)
0.0%
(-999.9 - +999.9%)
0
(0 - 2)