H2: Mfdo - YASKAWA GA800 Maintenance & Troubleshooting

3.10 H: Terminal Functions
Setting Value Function
17F !PID Bi-Directional Enable
19F !DWEZ Disable
◆

H2: MFDO

No.
Name
(Hex.)
H2-01 Term M1-M2 Function
Selection
(040B)
H2-02 Term M3-M4 Function
Selection
(040C)
H2-03 Term M5-M6 Function
Selection
(040D)
H2-06 Watt Hour Output Unit
Selection
(0437)
H2-07 Modbus Register 1 Address
Select
(0B3A)
H2-08 Modbus Register 1 Bit
Select
(0B3B)
H2-09 Modbus Register 2 Address
Select
(0B3C)
H2-10 Modbus Register 2 Bit
Select
(0B3D)
H2-20 Comparator 1 Monitor
Selection
(1540)
H2-21 Comparator 1 Lower Limit
(1541)
H2-22 Comparator 1 Upper Limit
(1542)
H2-23 Comparator 1 Hysteresis
(1543)
H2-24 Comparator 1 On-Delay
Time
(1544)
206
V/f CL-V/f OLV CLV AOLV
Switches the PID Bi-Directional output to enable or disable.
ON : Disable
OFF : Enabled
V/f CL-V/f OLV CLV AOLV
Switches the DriveWorksEZ program saved in the drive to enable or disable.
ON : Enabled
OFF : Disable
Note:
Set A1-07 = 2 [DriveWorksEZ Function Selection = Digital input] to use this function.
V/f CL-V/f OLV CLV AOLV
Sets the function for MFDO terminal M1-M2.
Note:
When you do not use the terminal or when you use the terminal in through mode, set this
parameter to F.
V/f CL-V/f OLV CLV AOLV
Sets the function for MFDO terminal M3-M4.
Note:
When you do not use the terminal or when you use the terminal in through mode, set this
parameter to F.
V/f CL-V/f OLV CLV AOLV
Sets the function for MFDO terminal M5-M6.
Note:
When you do not use the terminal or when you use the terminal in through mode, set this
parameter to F.
V/f CL-V/f OLV CLV AOLV
Sets the unit for the output signal when H2-01 to H2-03 = 39 [MFDO Function Selection = Watt
Hour Pulse Output].
0 : 0.1 kWh units
1 : 1 kWh units
2 : 10 kWh units
3 : 100 kWh units
4 : 1000 kWh units
V/f CL-V/f OLV CLV AOLV
Sets the address of the MEMOBUS/Modbus register output to the MFDO terminal.
V/f CL-V/f OLV CLV AOLV
Sets the bit of the MEMOBUS/Modbus register output to the MFDO terminal.
V/f CL-V/f OLV CLV AOLV
Sets the address of the MEMOBUS/Modbus register output to the MFDO terminal.
V/f CL-V/f OLV CLV AOLV
Sets the bit of the MEMOBUS/Modbus register output to the MFDO terminal.
V/f CL-V/f OLV CLV AOLV
Sets the monitor number for comparator 1. Set the x-xx part of the Ux-xx [Monitor]. For example, set
H2-20 = 102 to monitor U1-02 [Output Frequency].
V/f CL-V/f OLV CLV AOLV
Sets the lower limit detection level for comparator 1 when the full scale analog output for the monitor
selected in H2-20 [Comparator 1 Monitor Selection] is the 100% value.
V/f CL-V/f OLV CLV AOLV
Sets the upper limit detection level for comparator 1 when the full scale analog output for the monitor
selected in H2-20 [Comparator 1 Monitor Selection] is the 100% value.
V/f CL-V/f OLV CLV AOLV
Sets the hysteresis level for comparator 1 as a percentage of the full scale analog output for the
monitor selected in H2-20 [Comparator 1 Monitor Selection].
V/f CL-V/f OLV CLV AOLV
Sets the on-delay time for comparator 1.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
Default
(Range)
0
(0 - 1FF)
1
(0 - 1FF)
2
(0 - 1FF)
0
(0 - 4)
0001
(0001 - 1FFF)
0000
(0000 - FFFF)
0001
(0001 - 1FFF)
0000
(0000 - FFFF)
102
(000 - 999)
0.0%
(0.0 - 300.0%)
0.0%
(0.0 - 300.0%)
0.0%
(0.0 - 10.0%)
0.0 s
(0.0 - 600.0 s)