F2: Analog Input Option - YASKAWA GA800 Maintenance & Troubleshooting

No.
Name
(Hex.)
F1-37 Encoder 2 Signal Selection
(03BD)
F1-46 dv2 Detection Method
Selection
(1B98)
F1-47 Deviation 2 Detection
Selection
(1B99)
F1-50 PG-F3 Option Encoder Type
(03D2)
F1-51 PG-F3 PGoH Detection
Level
(03D3)
F1-52 Serial Encoder Comm Speed
(03D4)
◆

F2: Analog Input Option

No.
Name
(Hex.)
F2-01 Analog Input Function
Selection
(038F)
F2-02 Analog Input Option Card
Gain
(0368)
RUN
F2-03 Analog Input Option Card
Bias
(0369)
RUN
YASKAWA TOEPYAIGA8001B GA800 Drive Maintenance & Troubleshooting
V/f CL-V/f OLV CLV AOLV
Sets the number of channels for the signal to the encoder option card for motor 2.
0 : A Pulse Detection
1 : AB Pulse Detection
V/f CL-V/f OLV CLV AOLV
Usually it is not necessary to change this setting. Sets the detection method for dv2 [Z Pulse Noise
Fault Detection].
0 : ElectricalAngle Detection Method
1 : MechanicalAngle Detection Method
V/f CL-V/f OLV CLV AOLV
Usually it is not necessary to change this setting. Sets the sensitivity of detection for dv2 [Z Pulse
Noise Fault Detection]. Increase the value to decrease the sensitivity.
V/f CL-V/f OLV CLV AOLV
Sets the type of encoder connected to the PG-F3 option.
0 : EnDat Sin/Cos
1 : EnDat Serial Only
2 : HIPERFACE
V/f CL-V/f OLV CLV AOLV
The drive will detect PGoH [Encoder (PG) Hardware Fault] if the value of this parameter is smaller
than the value of
Note:
This function is enabled when F1-20 = 1 [Encoder 1 PCB Disconnect Detect = Enabled].
V/f CL-V/f OLV CLV AOLV
Sets the communication speed between the PG-F3 option and the serial encoder.
0 : 1M/9600bps
1 : 500k/19200bps
2 : 1M/38400bps
V/f CL-V/f OLV CLV AOLV
Sets the input method for the analog reference used with AI-A3.
0 : 3 Independent Channels
1 : 3 Channels Added Together
V/f CL-V/f OLV CLV AOLV
Sets the analog reference gain as a percentage when the maximum output frequency is 100%.
Note:
• Set F2-01 = 1 [Analog Input Function Selection = 3 Channels Added Together] to enable this
function.
• Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output
frequency.
–A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
–A1-02 = 8: E9-02 [Maximum Speed]
V/f CL-V/f OLV CLV AOLV
Sets the analog reference bias as a percentage when the maximum output frequency is 100%.
Note:
• Set F2-01 = 1 [Analog Input Function Selection = 3 Channels Added Together] to enable this
function.
• Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output
frequency.
–A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
–A1-02 = 8: E9-02 [Maximum Speed]
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
.
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
3.9 F: Options
Default
(Range)
0
(0, 1)
0
(0, 1)
15°
(0 - 180°)
0
(0 - 2)
80%
(1 - 100%)
0
(0 - 2)
Default
(Range)
0
(0, 1)
100.0%
(-999.9 - +999.9%)
0.0%
(-999.9 - +999.9%)
3
185