F2: Analog Input Card (Ai-A3) - YASKAWA A1000 Technical Manual

No.
(Addr. Name
Hex)
F1-18
dv3 Detection Selection
(3AD)
F1-19
dv4 Detection Selection
(3AE)
F1-20 PG Option Card Disconnect
(3B4) Detection 1
F1-21
PG 1 Signal Selection
(3BC)
F1-30 PG Card Option Port for
(3AA) Motor 2 Selection
F1-31
PG 2 Pulses Per Revolution Sets the number of pulses for a PG option card connected to port CN5-B.
(3B0)
F1-32
PG 2 Rotation Selection
(3B1)
F1-33
PG 2 Gear Teeth 1
(3B2)
F1-34
PG 2 Gear Teeth 2
(3B3)
F1-35 PG 2 Division Rate for Pulse
(3BE) Monitor
F1-36 PG Option Card Disconnect
(3B5) Detection 2
F1-37
PG 2 Signal Selection
(3BD)
<1> Default setting is determined by parameter A1-02, Control Method Selection.
u

F2: Analog Input Card (AI-A3)

No.
(Addr. Name
Hex)
F2-01 Analog Input Option Card
(38F) Operation Selection
F2-02
Analog Input Option Card
(368)
Gain
F2-03
Analog Input Option Card
(369)
Bias
YASKAWA ELECTRIC TOEP C710616 41B YASKAWA AC Drive - A1000 Quick Start Guide
Description
0: Disabled
n: Number of dv3 occurrences that must be detected to trigger a dv3 fault.
0: Disabled
n: Number of pulses that the A and B pulse are reversed that triggers dv4
detection.
0: Disabled
1: Enabled
0: A pulse detection
1: AB pulse detection
Sets the port for the PG option card used by motor 2.
0: CN5-C
1: CN5-B
0: Pulse A leads
1: Pulse B leads
Sets the gear ratio between the motor shaft and the encoder (PG).
A gear ratio of 1 will be used if F1-33 or F1-34 are set to 0.
Sets the gear ratio between the motor shaft and the encoder (PG). A gear ratio
of 1 will be used if F1-33 or F1-34 are set to 0.
Sets the division ratio for the pulse monitor used of the PG option card 2
installed to port CN5-B.
By setting "xyz", the division ratio becomes = [(1 + x) / yz].
0: Disabled
1: Enabled
0: A pulse detection
1: AB pulse detection
Description
0: Option card input terminals V1, V2, and V3 replace drive input terminals
A1, A2, and A3.
1: Input signals to terminals V1, V2, and V3 are added together to create the
frequency reference.
Sets the gain for the input signal to the analog card.
Sets the bias for the input signal to the analog card.
B.6 F: Options
Values Page
Default: 10
Min.: 0 –
Max.: 10
Default: 128
Min.: 0 –
Max.: 5000
Default: 1
–
Range: 0, 1
Default: 0
–
Range: 0, 1
Default: 1
–
Range: 0, 1
Default: 1024 ppr
Min.: 1 –
Max.: 60000
Default: 0
–
Range: 0, 1
Default: 0
Min.: 0 –
Max.: 1000
Default: 0
Min.: 0 –
Max.: 1000
Default: 1
Min.: 1 –
Max.: 132
Default: 1
–
Range: 0, 1
Default: 0
–
Range: 0, 1
Values Page
Default: 0
–
Range: 0, 1
Default: 100.0%
Min.: -999.9 –
Max.: 999.9
Default: 0.0%
Min.: -999.9 –
Max.: 999.9
199
B