Mitsubishi FX3UC SERIES User Manual page 177

FX Series Programmable Controllers
3UC
User's Manual - Hardware Edition
6.2.2 Transistor Output Specifications (Source output type)
The table below shows the output specifications of the FX
extension blocks (source output type).
Outputs in the main unit are restricted by the simultaneous ON ratio.
Number of
output
points
Connecting type
Output type/form
External power supply
Resistance
load
Max.
load
Inductive
load
Open circuit leakage current
ON voltage
OFF → ON
Response
time
ON → OFF
Circuit insulation
Output operation
display
*1. When the two +V
→ For the restriction in simultaneous ON ratio, refer to Subsection 6.2.3.
Item
FX -16MT/DSS
3UC
FX -32MT/DSS
3UC
FX -64MT/DSS
3UC
FX -96MT/DSS
3UC
FX -8EYT-ESS/UL
2N
FX -16EYT-ESS/UL,
2N
FX -16EYT-DSS
2NC
FX -32EYT-DSS
2NC
FX - MT/DSS,
3UC
FX output extension block,
2NC
FX FX output extension block
2N/ 0N
Y000 to Y003
FX -
3UC
MT/DSS
Y004 or later
FX -16EYT-DS, FX -32EYT-DS 0.1A/1 points
2NC 2NC
FX -8EYT-ESS/UL,
2N
FX -16EYT-ESS/UL
2N
Y000 to Y003
FX -
3UC
MT/DSS
Y004 or later
FX -16EYT-DSS,
2NC
FX -32EYT-DSS
2NC
FX -8EYT-ESS/UL,
2N
FX -16EYT-ESS/UL
2N
Y000 to Y002
FX -
3UC
MT/DSS
Y003 or later
For FX Series
Extension 2NC
blocks
For FX Series
2N
Y000 to Y002
FX -
3UC
MT/DSS
Y003 or later
For FX Series
Extension 2NC
blocks
For FX Series
2N
FX - MT/DSS,
3UC
Extension blocks
terminals are connected outside the PLC, resistance load is 1.6A or less.
6 Output Specification and External Wiring
- MT/DSS Main unit, FX
3UC
Transistor output (source) specifications
8 points
16 points
32 points
48 points
8 points
16 points
32 points
Connector
Terminal block
Transistor/Source output
5 to 30V DC
0.3A/1 points Make sure that the total load
current of 8 resistance load points
0.1A/1 points
*1
is 0.8A or less.
Make sure that the total load
current of 8 resistance load points
is 0.8A or less.
The total load current of resistance
loads per common terminal should
0.5A/1 points be the following value.
4points/common: 0.8A
8points/common: 1.6A
7.2W/1 points
Make sure that the total load of 16
(24V DC)
inductive load points is 38.4W/24V
2.4W/1 points
DC or less.
(24V DC)
2.4W/1 points (24V DC)
12W/1 points (24V DC)
0.1mA or less/30V DC
1.5V or less
5µs or less/10mA or more (5 to 24V DC)
0.2ms or less/100mA (24V DC)
0.2ms or less/100mA
0.2ms or less/200mA
5µs or less/10mA or more (5 to 24V DC)
0.2ms or less/100mA (24V DC)
0.2ms or less/100mA
0.2ms or less/200mA
Photocoupler insulation
LED on panel lights when photocoupler is driven.
6.2 Transistor Output
1
/FX output
2NC 2N
2
3
4
5
6
7
8
9
10
171