Installation Process Overview - Barco DP2K-E series User And Installation Manual

4. Installation process
4.1

Installation process overview

Installation process from A to Z
1. Check if all installation requirements are fulfilled such as the environment conditions of the installation area, electrical facili-
ties, etc. Note that a solid pedestal is required to support the projector. For more info see topic installation requirements.
2. Physical installation of the projector upon its pedestal. See chapter "Positioning the DP2K-E series projector at port window",
page 24.
3. Electrical connection with the power net. See chapter "Connecting the projector with the power net", page 27.
4. Installation of a UPS to the projector electronics (if applicable). See chapter "Connecting a UPS to the projector electronics",
page 28.
5. Installation of the lens. First select a lens with appropriate throw ratio covering the screen size and the projector - screen
distance. Then install the lens in the lens holder of the projector. For more information about available lenses, lens selection and
lens installation see chapter "Lenses & Lens selection", page 31.
Caution: The projector is delivered with a plastic cover inside the Lens Holder. Remove the cover prior to installing the lens.
6. Installation of the ICMP (only in case no ICMP is factory installed).
7. Installation of the Communicator Touch Panel. See chapter "Installing the Touch Panel interface", page 72.
8. Switch on the projector. The projector can now be switched on. Place the ON/OFF switch of the projector in the "I" position.
As a result the projector starts to initialize. The status lights of the projector lights up GREEN once the projector is initialized. In
case the status lights up RED may indicate a tamper event during transport. If so, contact Barco customer service.
9. Select the corresponding lens parameters for the installed lens. See user guide of the Communicator chapter Installation >
Advanced > Lens parameters.
10.Alignment of the projected image on the screen. The image can be aligned with the screen size of the application. Follow
the next steps to achieve that:
a) Press the STANDBY button on the Local Keypad to activate the lamp.
b) Press the DOWSER button on the Local Keypad to open the electronic dowser of the projector. The electronic dowser is open
if the color of the DOWSER button is GREEN.
c) Press the TEST PATTERN button on the Local Keypad to project one of the internal test patterns of the projector on the
screen.
d) Perform a "Lens Homing". See user guide of the Communicator.
e) Use the lens ZOOM, SHIFT and FOCUS buttons on the Local Keypad to match the projected image with the screen. Tilt the
projector in case you can not SHIFT the image completely upon the screen. See "Positioning the DP2K-E series projector at
port window", page 24.
See chapter "Local Keypad", page 41, for detailed description of the Local Keypad buttons.
11. Adjusting the light path. Normally the lens holder and the convergence of the projector are perfectly adjusted at the factory.
Nevertheless, some applications require a readjustment of the lens holder, convergence or both. See procedure "Scheimpflug
adjustment", page 82, and "Convergence", page 91.
12.Creating screen files, lens files, light sensor calibration (LSC) files, and macro files for FLAT and for SCOPE. See user
guide of the Communicator.
13.Backup of all projector configuration files. See user guide of the Communicator.
14.Registration of the projector. The DP2K-E series projector is DCI compliant and should be registered.
15.Projection of a digital cinema movie.
Download the ICMP device certificate, request KDM and DCP from your content supplier, ingest KDM and DCP, and play out the
movie. for detailed instructions see chapter "ICMP", page 47, and user guide of the Communicator and/or (Web) Commander.
Use the Communicator (Touch Panel) to configure the applied source. See the user guide of the Communicator (Touch Panel)
for more detailed information.
22 R5906693 DP2K-E SERIES 19/06/2015