Konica Minolta 7020 Service Manual page 168

HOME
25
ADJUSTMENT
DIP SW
BIT
No.
0 Unit isolation (2)
1
2
DIP SW19 3
4
5
6
7
0 Unit isolation (3)
1
2
DIP SW20 3
4
5
6
7
0 Platen size recognition selector switch 1 for
Latin America (Inch only)
1 Platen size recognition selector switch 2 for
Latin America (Inch only)
2 Platen size recognition selector switch 3 for
3
Latin America (Inch only)
3 Notice of nonstandard small platen size
(Inch only) *15
4 Job suspension/end at pulling out key
DIP SW21 counter
5 Notice of small size of platen mode
3
(8.5x11/A4 or smaller)
6 Total-counter/key-counter increment
operation
When using an EKC, the password screen
7
appears at the end of each job.
3
(Other than 7020/25/30/35)
0 Turns ON the sub power switch when the
main power switch is turned ON.
1 Nonstandard size becomes effective at
automatic platen start
2 FM4 (internal cooling fan) connection switch
3
(7020/25/30/35)
DIP SW22
3
4 Indication of total count start day on P mode screen
5 Platen APS detected size enlargement
3
(7020/25/30/35)
6 Paper magnification correction according to paper size
3
7 Exit limit detect sensor (PS19) (7020/25/30/35)
Functions
*33 Printer board can be used
Fax board can be used
Scanner can be used
RADF can be used
*33
FNS can be used
8.5 x 11
8.5 x 11R
8.5 x 14
Notice of noticed size
If DIP SW1-0:0: Stop paper
feed and terminate
If DIP SW1-0:1 Immediate-
stop jam
*15
Notice size detected by APS.
Normal operation (Both the total
counter and the key counter count
up regardless of the mode.)
No
No
*34
No
*35
Connecting
–
Not indicated
Size detection enlargement
Invalid
Exist
0
Printer board is isolated
Fax board is isolated
–
–
–
Scanner is isolated
–
RADF is isolated
–
–
–
–
FNS offset mode cannot be used
–
–
–
A4
A4R
F4
Notice as nonstandard size
If DIP SW1-0:0: Stop paper
feed and printing is interrupted
If DIP SW1-0:1 Immediate-
stop jam
Notice size as A4 (Japan, Metric)
or 8.5x11 (Inch)
During a copy mode, both the total
counter and the key counter count
up. During a printer/Fax mode,
only the total counter is counted up.
Yes
Yes (WUT increase)
Yes (only by-pass tray)
Disconnecting
–
Indicated
Detected size at commencement
of mass-production
Valid
Not exist
4-10
Default values
1
Japan
Inch
0 0
0 0
– 0 0
–
0 0
– 0
0
0 0
–
0 0
0 0
– 0 0
–
0 0
– 0 0
–
0 0
0
0
– 0 0
–
0 0
– 0
0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
– 0 0
0 0
0
0
0
0
1
1
Metric
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1