Sony PDW-HD1500 Operation Manual page 42

Item Setting
F2: A2 INPUT Selects the audio input signal to assign
to audio channel 2.
SDI: Audio signal embeded into SDI
ANALOG2: Analog 2 audio signal
AES/EBU: Signal input to the DIGITAL
i.LINK: Audio signal embeded into
SG: Test signal from internal signal
F3: MONITR L Selects the channel to monitor as the left
monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F4: MONITR R Selects the channel to monitor as the
right monitor channel.
CH1, CH2, CH3, CH4, CH5, CH6, CH7,
CH1/2, CH3/4, CH5/6, CH7/8 (MIX)
F5: SPEAKER Enables or disables output from this
unit's speaker.
OFF: Do not output
ON: Output
F6: LEVEL MT Specifies the position at which to
superimpose audio level meters in the
video monitor screen (in full-screen
display mode).
OFF: Do not superimpose.
LEFT: Superimpose the audio level
RIGHT: Superimpose the audio level
LEFT(4): Superimpose the audio level
RIGHT(4): Superimpose the audio level
LEFT(8): Superimpose the audio level
RIGHT(8): Superimpose the audio level
P3 AUDIO page
Item Setting
F1: A3 INPUT Selects the audio input signal to assign
to audio channel 3.
SDI: Audio signal embeded into SDI
ANALOG1: Analog 1 audio signal
AES/EBU: Signal input to the DIGITAL
i.LINK: Audio signal embeded into
SG: Test signal from internal signal
42
Basic Operations of the Function Menu
signal
AUDIO(AES/EBU) IN 1/2 connectors
i.LINK input
generator (Selection is carried out
with A1 INPUT.)
CH8
CH8
meters of 2 channels on the left side.
meters of 2 channels on the right
side.
meters of 4 channels on the left side.
meters of 4 channels on the right
side.
meters of 8 channels on the left side.
meters of 8 channels on the right
side.
signal
AUDIO(AES/EBU) IN 3/4 connectors
i.LINK input
generator (Normally this item is not
displayed. It appears when you hold
the button down for 3 seconds.)
Item Setting
F2: A4 INPUT Selects the audio input signal to assign
to audio channel 4.
SDI: Audio signal embeded into SDI
signal
ANALOG2: Analog 2 audio signal
AES/EBU: Signal input to the DIGITAL
AUDIO(AES/EBU) IN 3/4 connectors
i.LINK: Audio signal embeded into
i.LINK input
SG: Test signal from internal signal
generator (Selection is carried out
with A3 INPUT.)
F3: (Unassigned function button)
F4: (Unassigned function button)
F5: (Unassigned function button)
F6: (Unassigned function button)
P4 TC page
Item Setting
F1: TCG Selects the timecode signal to which the
internal timecode generator
synchronizes.
INT: Follow the initial value set from the
control panel or remotely from the
device connected to the
REMOTE(9P) connector, or
synchronize to timecode played
back from the disc.
EXT: Synchronize to external timecode
input to the TIME CODE IN
connector.
SDI: Synchronize to timecode embeded
into HDSDI signal input to HDSDI
INPUT connector.
F2: PRST/RGN Selects the following for the internal
timecode generator.
PRESET: Presets an initial value for the
timecode generated by the internal
timecode generator, as specified
from the control panel or remotely
from the device connected to the
REMOTE(9P) connector. This is
valid when "INT" is selected with the
F1: TCG item on this page. The
operation is the same as "TC" when
anything else is selected.
TC: Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC: Generate timecode synchronized
to VITC read by the internal
timecode reader.
F3: RUN MODE Selects the timecode run mode.
FREE: Timecode advances as long as
the unit is powered on, regardless of
the unit's operating state.
REC: Timecode advances only during
recording. When you select this
item, also set F1: TCG on this page
to "INT" and set F2: PRST/RGN to
"PRESET".