Sony HDW-750 Maintenance Manual page 187

CCD ADJUST Display (Adjusting CCD block)
O
? 04 CCD ADJUST
R VSUB
G VSUB
B VSUB
R VSUB OFST 500 :
G VSUB OFST 500 :
B VSUB OFST 500 :
OUTPUT SELECT
The version of AT is before Ver 1.40
Item Setting
R VSUB 9.4 V to 19.5 V/(_99 to 99)
G VSUB 9.4 V to 19.5 V/(_99 to 99)
B VSUB 9.4 V to 19.5 V/(_99 to 99)
_5.0 V to 5.0 V/(_99 to 99)
R VSUB OFST 500
G VSUB OFST 500 _5.0 V to 5.0 V/(_99 to 99)
B VSUB OFST 500 _5.0 V to 5.0 V/(_99 to 99)
*2 _5.0 V to 5.0 V
R VSUB (P)
G VSUB (P) *2 _5.0 V to 5.0 V
*2
B VSUB (P) _5.0 V to 5.0 V
OUTPUT SELECT Y/R/G/B/RGB
*1 : When the unit of which the ROM version of the AT board is before 1.40, the value is displayed in the relative value. When the unit of
which the ROM version of the AT board is 1.40 and higher, the value is displayed in the absolute value.You can check the AT
version by the ROM VERSION display in the DIAGNOSIS menu.
*2 : This item is displayed only when the Camcorder is HDW-750P and the AT version is 1.40 and higher.
*3 : RGB can be selected only when the Camcorder is used in the service mode.
HDW-750/750CE V1
? 04
: 0 R VSUB
: 0 G VSUB
: 0 B VSUB
R VSUB OFST 500 : +0.0V
0
G VSUB OFST 500 : +0.0V
0
B VSUB OFST 500 : +0.0V
0
R VSUB(P)
: Y G VSUB(P)
B VSUB(P)
OUTPUT SELECT
The version of AT is Ver 1.40 and Higher
Function
*1
Sets the V. substrate voltage value of the R-channel.
*1 Sets the V. substrate voltage value of the G-channel.
*1 Sets the V. substrate voltage value of the B-channel.
*1
Sets the V. substrate voltage value of the R-channel.
(This is the adjustment for offset when shutter speed is
higher than 1/500.)
*1
Sets the V. substrate voltage value of the G-channel.
(This is the adjustment for offset when shutter speed is
higher than 1/500.)
*1 Sets the V. substrate voltage value of the B-channel.
(This is the adjustment for offset when shutter speed is
higher than 1/500.)
Sets the V. substrate voltage value of the R-channel.
(This is the adjustment for offset when the format is 25PsF.)
Sets the V. substrate voltage value of the G-channel.
(This is the adjustment for offset when the format is 25PsF.)
Sets the V. substrate voltage value of the B-channel.
(This is the adjustment for offset when the format is 25PsF.)
*3
Selects the video signal that is output from the TEST OUT
and the VBS/SDI OUT terminal. (The Y-signal becomes the
VBS signal when the REAR BNC OUT SEL of the OUTPUT
SEL display of the OPERATION menu selects the VBS
position and when the TEST OUT SELECT chooses the SD
position.) The output signal returns to the Y-signal without
fail at power-on.
O
CCD ADJUST
: 14.4V
: 14.4V
: 14.4V
: +0.0V
: +0.0V
: +0.0V
:
4-9. SERVICE Menu
Y
4-65