AMX NXA-ENET8-2POE Operation/Reference Manual page 86

Configuring the NXA-ENET8-2POE
Access Control List Configuration parameters (Cont.)
• IPv4 (Cont.)
Response to take when a rule is matched
• Action
• Rate Limiter
• Port Copy
• Mirror
76
TCP RST Specifies the TCP Reset the connection (RST) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the
RST field is set must not match this entry, 1 - TCP frames where
the RST field is set must match this entry; Default: Any)
TCP PSH Specifies the TCP Push Function (PSH) value for this rule.
(Options: Any - any value is allowed, 0 - TCP frames where the
PSH field is set must not match this entry, 1 - TCP frames where
the PSH field is set must match this entry; Default: Any)
TCP ACK Specifies the TCP Acknowledgment field significant (ACK) value
for this rule. (Options: Any - any value is allowed, 0 - TCP frames
where the ACK field is set must not match this entry, 1 - TCP
frames where the ACK field is set must match this entry; Default:
Any)
TCP URG Specifies the TCP Urgent Pointer field significant (URG) value for
this rule. (Options: Any - any value is allowed, 0 - TCP frames
where the URG field is set must not match this entry, 1 - TCP
frames where the URG field is set must match this entry; Default:
Any)
IP TTL Specifies the time-to-Live settings for this rule. (Options: Any - any
value is allowed, Non-zero - IPv4 frames with a TTL field greater
than zero must match this entry, Zero - IPv4 frames with a TTL
field greater than zero must not match this entry; Default: Any)
IP Fragment Specifies the fragment offset settings for this rule. This involves
the settings for the More Fragments (MF) bit and the Fragment
Offset (FRAG OFFSET) field for an IPv4 frame. (Options: Any -
any value is allowed, Yes - IPv4 frames where the MF bit is set or
the FRAG OFFSET field is greater than zero must match this
entry, No - IPv4 frames where the MF bit is set or the FRAG OFF-
SET field is greater than zero must not match this entry; Default:
Any)
IP Option Specifies the options flag setting for this rule. (Options: Any - any
value is allowed, Yes - IPv4 frames where the options flag is set
must match this entry, No - IPv4 frames where the options flag is
set must not match this entry; Default: Any)
SIP Filter Specifies the source IP filter for this rule. (Options: Any - no source
IP filter is specified, Host - specifies the source IP address in the
SIP Address field, Network - specifies the source IP address and
source IP mask in the SIP Address and SIP Mask fields; Default:
Any)
DIP Filter Specifies the destination IP filter for this rule. (Options: Any - no
destination IP filter is specified, Host - specifies the destination IP
address in the DIP Address field, Network - specifies the destina-
tion IP address and destination IP mask in the DIP Address and
DIP Mask fields; Default: Any)
Permits or denies a frame based on whether it matches an ACL rule. (Default: Permit)
Specifies a rate limiter (page 91) to apply to the port. (Range: 1-16; Default: Disabled)
Defines a port to which matching frames are copied. (Range: 1-10; Default: Disabled)
Mirrors matching frames from this port. (Default: Disabled) See the Configuring Port
Mirroring section on page 140.
ACL-based port mirroring set by this parameter and port mirroring set on the general
Mirror Configuration page are implemented independently. To use ACL-based mirror-
ing, enable the Mirror parameter on the ACE Configuration page. Then open the Mir-
ror Configuration page, set the Port to mirror on field to the required destination port,
and leave the Mode field Disabled.
NXA-ENET8-2POE Gigabit Ethernet Layer 2 PoE Switch