Specifications 3.5L Engine - Chrysler 300M Service Manual

LH
ENGINE 3.5L (Continued)
(6) Tighten engine mount fastener to 61 N·m (45
ft. lbs.).
(7) Align flex plate to torque converter and install
mounting bolts. Tighten bolts to 75 N·m (55 ft. lbs.).
(8) Install crankshaft position sensor. (Refer to 14 -
FUEL SYSTEM/FUEL INJECTION/CRANKSHAFT
POSITION SENSOR - INSTALLATION)
(9) Install starter. (Refer to 8 - ELECTRICAL/
STARTING/STARTER MOTOR - INSTALLATION)
(10) Install new V-Band clamp at left side exhaust
manifold to catalytic converter. Tighten V-Band
clamp to 11 N·m (100 in. lbs.).
(11) Install left side catalytic converter down pipe
support fastener at transaxle. Tighten fastener to 47
N·m (35 ft. lbs.).
(12) Tighten the left converter down pipe band clamp.
(13) Install the transmission
bracket to engine.
(14) Install structural collar/cover. (Refer to 9 -
ENGINE/ENGINE BLOCK/STRUCTURAL COVER -
INSTALLATION)
(15) Lower vehicle.
(16) Connect all electrical connections.
(17) Install four upper transmission to block bolts
tighten to 102 N·m (75 ft. lbs.).
(18) Install water pipe and retaining fasteners to
the transaxle/cylinder block double-ended bolts.
(19) Install rear throttle body support bracket.
(20) Connect heater hoses.
(21) Install upper intake manifold. (Refer to 9 -
ENGINE/MANIFOLDS/INTAKE
INSTALLATION)
(22) Connect ground straps at both cylinder heads.
(23) Connect all vacuum hoses.
(24) Connect coolant hoses at coolant recovery/
pressure container.
(25) Connect throttle and speed control cables to
bracket and throttle arm. (Refer to 14 - FUEL SYS-
TEM/FUEL INJECTION/THROTTLE
CABLE - INSTALLATION)
(26) Connect fuel line. (Refer to 14 - FUEL SYS-
TEM/FUEL DELIVERY/FUEL LINES - STANDARD
PROCEDURE)
(27) Install new V-Band clamp at right exhaust man-
ifold. Tighten V-Band clamp to 11 N·m (100 in. lbs.).
(28) Install and tighten right side catalytic con-
verter down pipe support bracket fastener at trans-
axle mount.
(29) Install air conditioning
tighten fasteners to 28 N·m (250 in. lbs.).
(30) Install power steering pump and tighten fas-
teners to 28 N·m (250 in. lbs.).
(31) Install generator. (Refer to 8 - ELECTRICAL/
CHARGING/GENERATOR - INSTALLATION)
(32) Install radiator. (Refer to 7 - COOLING/EN-
GINE/RADIATOR - INSTALLATION)
lines to radiator.
COOLING/ACCESSORY DRIVE/DRIVE BELTS -
INSTALLATION) .
ENGINE/RADIATOR FAN - INSTALLATION)
STANDARD PROCEDURE)
install upper radiator crossmember. (Refer to 23 -
oil cooler lines BODY/EXTERIOR/GRILLE OPENING REINFORCE-
MENT - INSTALLATION)
EXTERIOR/FRONT STRUT TOWER TO TOWER
BRACE - INSTALLATION)
EXTERIOR/COWL
INSTALLATION)
TRICAL/WIPERS/WASHERS/WIPER
INSTALLATION)
HOOD - INSTALLATION)
MANIFOLD -
SPECIFICATIONS
3.5L ENGINE
Type
CONTROL
Displacement
Bore and Stroke
Compression Ratio
Lead Cylinder
Firing Order
compressor and
Cylinder Bore Diameter
Out-of-Round (Max.)
Taper (Max.)
(33) Attach air conditioning condenser to radiator.
(34) Install power steering line bracket to radiator.
(35) Connect engine oil and transmission cooler
(36) Install lower radiator hose.
(37) Install upper radiator hose.
(38) Install accessory drive belts. (Refer to 7 -
(39) Install radiator fan. (Refer to 7 - COOLING/
(40) Fill cooling system. (Refer to 7 - COOLING -
(41) Fill engine with proper amount of oil.
(42) Connect hood release cable to hood latch and
(43) Install air cleaner and air inlet hose.
(44) Install strut tower brace. (Refer to 23 - BODY/
(45) Install both cowl covers. (Refer to 23 - BODY/
GRILLE
(46) Install both wiper arms. (Refer to 8 - ELEC-
(47) Install hood. (Refer to 23 - BODY/HOOD/
(48) Connect negative cable.
DESCRIPTION
Cylinder Block
ENGINE 9 - 15
AND SCREEN
ARMS
SPECIFICATION
60° SOHC V-6 24-Valve
3.5 Liters
(214 Cubic Inches)
96.0 x 81.0 mm
(3.780 x 3.189 in.)
9.9:1
#1 Right Bank
1-2-3-4-5-6
96.0 mm ±0.0076
(3.780 in. ±0.0003 in.)
0.076 mm
(0.003 in.)
0.051 mm
(0.002 in.)
-
-