Daikin VRV III-S RXYMQ36 48PVJU Service Manual page 72

SiUS34-907
3.1.4 Setting Contents and Code No. – VRV Indoor unit
Mode
First
No.
Code
No.
Note 2
Filter contamination heavy/
light (Setting for display
time to clean air filter)
0 (Sets display time to clean
air filter to half when there
is heavy filter
contamination.)
10(20)
1 Long-life filter type
2 Thermostat sensor in remote controller
Display time to clean air filter calculation
3
(Set when filter sign is not to be displayed.)
Optional accessories output selection (field
0
selection of output for adaptor for wiring)
ON/OFF input from outside (Set when ON/
1
OFF is to be controlled from outside.)
Thermostat differential changeover
2
VRV
(Set when remote sensor is to be used.)
system
12(22)
Airflow setting when heating thermostat is
indoor
3
OFF
unit
settings
Automatic mode differential (automatic
4 temperature differential setting for VRV
system heat recovery series cool/heat)
5 Power failure automatic reset
Airflow setting when Cooling thermostat is
6
OFF
0 Setting of normal airflow
Selection of airflow direction
1 (Set when a blocking pad kit has been
installed.)
3 Operation of downward flow flap: Yes/No
13(23)
4 Field set airflow position setting
5 Setting of static pressure selection
1 Thermostat OFF excess humidity
Direct duct connection
(when the indoor unit and heat reclaim
2
ventilation unit are connected by duct
15(25) directly.) ∗Note 5
3 Drain pump humidifier interlock selection
Field set selection for individual ventilation
5
setting by remote controller
Notes :
1. Settings are made simultaneously for the entire group, however, if you select the mode No. inside
parentheses, you can also set by each individual unit. Setting changes however cannot be checked except in
the individual mode for those in parentheses.
2. The mode numbers inside parentheses cannot be used by wireless remote controllers, so they cannot be set
individually. Setting changes also cannot be checked.
3. Do not make settings other than those described above. Nothing is displayed for functions the indoor unit is
not equipped with.
4. "88" may be displayed to indicate the remote controller is resetting when returning to the normal mode.
5. If the setting mode to "Equipped", heat reclaim ventilation fan conducts the fan residual operation by linking to
indoor unit.
Test Operation
Setting Contents
Ultra long-life
filter
Long-life filter
Standard
filter
Second Code No.
01 02
Approx. Approx.
10,000
hrs.
Approx. Approx.
Light 2,500 Heavy
hrs.
Approx. Approx.
200
hrs.
Long life filter Ultra long-life filter
Remote
Only body
controller + Body
thermostat
thermostat
Display No display
Indoor unit
turned ON by —
thermostat
Forced OFF ON/OFF control
1.8°F 0.9°F
LL Set fan speed
01:0 02:1 03:2
Not equipped Equipped
LL Set fan speed
N H
F (4 directions) T (3 directions)
Equipped Not equipped
Draft prevention Standard
High static
Standard
pressure
Not equipped Equipped
Not equipped Equipped
Not equipped Equipped
Not equipped Equipped
: Factory setting
03
5,000
hrs.
—
1,250
hrs.
100
hrs.
—
Only remote
controller
thermostat
—
Operation Malfunction
output output
External
protection
device input
—
—
04:3 05:4 06:5 07:6
—
—
S
W (2
directions)
—
Ceiling
Soiling
prevention
—
—
—
—
—
Field Setting
Details
No
04
— (1)
(2)
—
(3)
—
(4)
—
(5)
(6)
—
(7)
—
(8)
—
08:7 —
(9)
—
(10)
—
(11)
—
(12)
—
(13)
—
(14)
—
(15)
—
(16)
—
(17)
—
(18)
—
(19)
—
63