Agilent Technologies E8362C Service Manual page 378

Index
RS-232 port
,
rear panel connector 5-32
,
troubleshooting 4-18
S
safety
,
considerations 1-3
,
earth ground 1-3
,
symbols 1-3
,
SCPI 8-9
screws
for bottom assemblies
, ,
illustrated 6-71 6-73
, ,
part numbers 6-70 6-72
serial number
,
changing 8-18
,
installing 8-18
SERIAL port
,
rear panel connector 5-32
,
troubleshooting 4-18
service
EMI/RFI parts
,
part numbers 6-86
,
options 2-11
procedures
,
caution about 7-3
,
post-repair 7-82
,
pre-repair 7-3
,
warnings about 7-3
static safety parts
,
part numbers 6-86
,
required 2-10
test equipment
,
required 2-8
tools
,
part numbers 6-84
,
required 2-10
,
warnings 1-4
warranty
,
one-year return to Agilent 2-11
,
standard 2-11
,
shipment for service or repair 2-12
signal separation
,
functional description of 5-4
,
functional group 5-3
signal separation group
,
block diagram 5-17
,
defined 4-27
,
operation 5-16
,
troubleshooting 4-38
,
single band failure 4-31
software
,
options 8-16
SOMA 50
,
illustrated 6-23
,
operation 5-11
,
part number 6-22
removal and replacement
Index-16
,
illustrated 7-43
,
procedure 7-42
,
troubleshooting 4-32
source
,
calibration 3-45
,
functional group 5-3
,
maximum output power test 3-31
,
operation 5-6
,
power accuracy test 3-30
,
power linearity test 3-31
source 20
, ,
illustrated 6-15 6-19
,
operation 5-10
, ,
part numbers 6-14 6-18
removal and replacement
,
illustrated 7-23
,
procedure 7-22
,
troubleshooting 4-32
,
any band 4-46
source attenuators
,
description of 2-6
,
operation 5-18
removal and replacement
,
illustrated 7-59
,
procedure 7-58
source group
,
block diagram 5-7
,
defined 4-27
,
troubleshooting 4-30
source match
,
cause of failure 8-12
,
definition of 8-12
,
measurements affected by 8-12
SPAM board
, ,
illustrated 6-15 6-19
operation
,
analog 5-23
,
digital 5-31
, ,
part number 6-14 6-18
removal and replacement
,
illustrated 7-19
,
procedure 7-18
,
troubleshooting 4-43
speaker
,
front panel 5-30
,
troubleshooting 4-12
specifications
,
instrument 3-6
,
stabilization, warm up time 3-4
,
system 3-6
splitter
,
illustrated 6-23
,
operation 5-9
,
part number 6-22
removal and replacement
,
illustrated 7-39
,
procedure 7-38
stabilization
,
warm up time 3-4
standards compliant calibration
,
built-in tests, Option 898 2-6
static safety parts
,
required for servicing 2-10
step attenuator, receiver
, , ,
illustrated 6-39 6-41 6-45
,
operation 5-18
, , , ,
part number 6-38 6-40 6-42
6-62
removal and replacement
,
illustrated 7-71
,
procedure 7-70
step attenuator, source
, , , ,
illustrated 6-27 6-29 6-35 6-37
, , , ,
6-39 6-41 6-45 6-51 6-53
, , , ,
6-57 6-59 6-61 6-63 6-65
,
operation 5-18
, , , ,
part number 6-26 6-28 6-34
, , , ,
6-40 6-42 6-50 6-54 6-58
port 1
,
troubleshooting 4-40
port 2
,
troubleshooting 4-40
port 1
, , , ,
illustrated 6-27 6-29 6-35
, , , ,
6-39 6-41 6-45 6-51
, , , ,
6-55 6-57 6-59 6-61
6-65
, , ,
part number 6-26 6-28 6-34
, , , ,
6-40 6-42 6-50 6-54
6-62
port 2
, , , ,
illustrated 6-27 6-29 6-35
, , , ,
6-39 6-41 6-45 6-51
, , , ,
6-55 6-57 6-59 6-61
6-65
, , ,
part number 6-26 6-28 6-34
, , , ,
6-40 6-42 6-50 6-54
6-62
removal and replacement
,
illustrated 7-59
,
procedure 7-58
storage data
,
IDE 5-32
strap handle
analyzer
,
illustrated 6-77
,
part number 6-76
subgroup
data acquisition and processing
,
front panel 5-28
,
subnet mask, LAN 4-20
substitution
,
cable 3-22
,
calibration kits 3-22
,
verification kits 3-22
supplies
Service Guide E8364-90038
,
6-58
,
, ,
6-55
,
6-38
,
6-62
,
6-37
,
6-53
,
6-63
, ,
6-38
,
6-58
,
6-37
,
6-53
,
6-63
, ,
6-38
,
6-58
,
5-28