Agilent Technologies E8362C Service Manual page 368

Index
channel R1 receiver module
,
troubleshooting 4-43
channel R2
,
troubleshooting 4-26
channel R2 receiver module
,
troubleshooting 4-43
checks
cable
connector repeatability, failure of
3-18
,
insertion loss, failure of 3-14
magnitude and phase stability,
,
failure of 3-16
,
return loss, failure of 3-13
, ,
test port cables 3-10 3-12
,
operator's 3-10
,
accessories used in 3-10
,
dialog box 3-11
,
failure of 3-11
,
performing 3-10
,
Port 1 3-10
,
Port 2 3-10
,
preliminary 3-10
,
system 3-1
,
getting ready 3-4
test port cable
,
accessories used in 3-12
,
connector repeatability 3-17
,
insertion loss 3-14
magnitude and phase stability
,
performing 3-12
,
return loss 3-13
,
COM 8-9
commercial calibration
,
built-in tests, Option 897 2-6
,
compression test, receiver 3-33
,
configurable test set, Option 014 2-3
,
block diagram 5-19
,
operation 5-18
configuration
,
high dynamic range 5-20
,
diagram 5-20
,
Option 014 5-19
connector
care
,
principles of 3-5
,
quick reference 3-5
protective end caps
,
part numbers 6-84
repeatability check
,
failure of 3-18
,
of test port cables 3-17
connector repeatability
check
,
test port cables 3-17
connectors
,
care of 3-5
,
front panel 5-30
,
USB 5-30
Index-6
, ,
rear panel 5-10 5-12
,
1284-C 5-32
,
8.33 MHz IF IN 5-26
, ,
AUX I/O 5-12 5-15
,
Display 5-32
EXT 10 MHz REF IN
EXT 10 MHz REF OUT
,
GPIB 5-32
,
,
HANDLER I/O 5-12
,
PARALLEL 5-32
,
PULSE IN 5-26
,
RS-232 5-32
,
SERIAL 5-32
TEST SET DRIVERS
,
TEST SET I/O 5-12
,
TRIG IN 5-12
,
TRIG OUT 5-12
,
USB 5-32
,
VGA 5-32
constants
,
correction 8-21
controller board, touch screen
removal and replacement
,
illustrated 7-13
,
procedure 7-12
controllers
troubleshooting with
,
correction constants
coupler
,
LO path
3-15
,
operation 5-26
nut
, ,
illustrated 6-71
,
part number 6-70
port 1
,
illustrated 6-23
,
part number 6-22
,
troubleshooting
port 2
,
illustrated 6-23
,
part number 6-22
,
troubleshooting
RF path
,
operation 5-26
coupler, LO path
removal and replacement
,
illustrated 7-75
,
procedure 7-74
coupler, RF path
removal and replacement
,
illustrated 7-75
,
procedure 7-74
,
cover, removing 1-4
covers, analyzer
,
illustrated 6-77
,
part numbers 6-76
removal and replacement
,
illustrated 7-7
,
5-32 procedure
CPU board
illustrated
operation
part number
,
removal and replacement
5-10
,
illustrated
5-10
procedure
,
troubleshooting
5-14
cross talk
system test
test port test
cross-over cable, LAN
CSA mark
,
5-26
,
5-13
dangerous voltage
data acquisition
operation
data acquisition and processing
subgroup
data storage
hard disk
,
IDE
data, option
recovering
,
4-19
repairing
8-21
,
DCOM
description
functional
digital control group
digital processing group
6-73
freqeuency offset group
,
6-72
power supply group
receiver group
signal separation group
synthesized source group
4-40
detector
channel R1
illustrated
operation
4-40
part number
removal and replacement illustrated
removal and replacement procedure
channel R1, Option 014/080/081
illustrated
channel R1, Option 081
part number
channel R2
illustrated
operation
part number
removal and replacement illustrated
removal and replacement procedure
,
7-6
, ,
6-15 6-19
,
5-31
, ,
6-14 6-18
,
7-30
,
7-28
,
4-17
,
3-36
,
3-36
,
4-22
,
1-8
D
,
1-4
,
5-31
,
5-28
,
5-32
5-32
,
8-17
,
8-17
8-9
,
5-5
,
5-5
, ,
5-4 5-5
,
5-5
,
5-4
,
5-4
,
5-4
,
6-23
,
5-17
,
6-22
7-49
7-48
, ,
6-47 6-49
,
6-46
,
6-23
,
5-17
,
6-22
7-49
7-48
Service Guide E8364-90038
,
,
,
,