Agilent Technologies E8362C Service Note
Pna microwave network analyzers
Hide thumbs
Also See for E8362C:
- Service manual (382 pages) ,
- Installation note (30 pages) ,
- Service note (4 pages)
Advertisement
Quick Links
M
O
D
I
F
I
C
A
T
I
O
N
M
O
D
I
F
I
C
A
T
I
O
N
M
O
D
I
F
I
C
A
T
I
O
N
S E R V I C E
E8362C PNA Microwave Network Analyzers
Serial Numbers:
MY00000000-MY48500000, SG00000000-SG48500000, US00000000-US48500000
A new touchscreen display inverter shield is available to improve PNA noise
floor performance.
Parts Required:
P/N
N5230-00017
Inverter Shield
ADMINISTRATIVE INFORMATION
SERVICE NOTE CLASSIFICATION:
MODIFICATION RECOMMENDED
ACTION
ON SPECIFIED FAILURE
CATEGORY:
LOCATION
CATEGORY:
ON-SITE
SERVICE CENTER
PRODUCT'S SUPPORT LIFE
AVAILABILITY:
Calibration Not Required
ADDITIONAL INFORMATION: Affected PNA Models: E836xC & E8362/3/4CH85. Service Note History: E8362C-01 released
Jan 2009. E8362C-01a released Dec 5, 2012 to revise serial numbers.
© AGILENT TECHNOLOGIES, INC. 2012
PRINTED IN U.S.A.
December 5, 2012
Rev. 20
R
E
C
O
M
M
E
N
D
E
D
R
E
C
O
M
M
E
N
D
E
D
R
E
C
O
M
M
E
N
D
E
Description
D
Qty.
1
STANDARDS
LABOR: 0.5 Hours
SERVICE
N/A
INVENTORY:
NO CHARGE AVAILABLE UNTIL: end of service life
PRODUCT LINE: WN
AUTHOR: MF
E8362C-01A
N O T E
Supersedes:
E8362C-01
USED
PARTS:
SCRAP
Page 1 of 6
Advertisement
Related Manuals for Agilent Technologies E8362C
Summary of Contents for Agilent Technologies E8362C
- Page 1 Calibration Not Required PRODUCT LINE: WN AUTHOR: MF ADDITIONAL INFORMATION: Affected PNA Models: E836xC & E8362/3/4CH85. Service Note History: E8362C-01 released Jan 2009. E8362C-01a released Dec 5, 2012 to revise serial numbers. © AGILENT TECHNOLOGIES, INC. 2012 PRINTED IN U.S.A.
- Page 2 Service Guide information, use the following steps: 1. Go to http://www.agilent.com. 2. Enter your PNA model number (Ex: E8362C) in the Search box and click Search. 3. Scroll down to the heading Manuals and click on the title/hyperlink for the Service Guide. If you don’t find your Service Guide listed on the Web page that is displayed initially, click on the More...
- Page 3 Page 3 of 6 E8362C-01A Figure 1: Old inverter shield N5230-00013 9. Loosen the two screws on the inverter shield shown in Figure 2, using a T-10 wrench. Figure 2 10. Remove the two screws from the PCB shown in Figure 3, using a T-10 wrench.
- Page 4 Page 4 of 6 E8362C-01A Remove the two screws from the PCB With T-10 wrench Remove the three cables from the PCB Slide the PCB into the new shield (N5230-00017), as shown in Figure 4 Figure 4 12. Position the shield and PCB on the display assembly frame, as shown in Figure 5.
- Page 5 Page 5 of 6 E8362C-01A...
- Page 6 Page 6 of 6 E8362C-01A 13. The finished repair is shown in Figure 6. Figure 6 14. Replace the front panel assembly on the PNA as per “Removing and Replacing the Front Panel Assembly” in the Service Guide.