Multitech SocketModem iCell MTSMC-G2-IP At Commands Reference Manual page 102

Display Association Information – #WLANASSOCINFO
............................................................................. 64
Display Auto Discovery Commands – #VAUTODISC45
Display Configuration of DNS Servers – #VDNS43, 50
Display Current State of Physical Connection –
#VSTATE ............................................................. 15
Display DNS Table – #IPDNSTABLE ....................... 50
Display Email Parameters for Respective Mail ID –
#VMAILi ................................................................ 24
Display FTP Parameters – #VFTP ........................... 31
Display IP Addresses – #DISPLAYIP ....................... 76
Display Physical Parameters – #VPHY .................... 77
Display PING Parameters – #VPING ....................... 39
Display PPP Parameters – #VPPP .......................... 76
Display SMTP Parameters – #VSMTP ..................... 24
Display Software Version – #VVERSION ................. 15
Display TCP Parameters – #VTCP .......................... 35
Display the WLAN Profile – #WLANPROFILE ......... 63
Display UDP Module Configuration – #VUDP .......... 37
Download Files from FTP Server – #FTPGET ......... 30
DSR On or Off – &S ................................................. 11
DTE-DCE Character Framing – +ICF....................... 12
DTR Option – &D ..................................................... 11
E
Enable Power Save at Boot – #WLANPOWERSAVE62
Enable/Disable and Configure External GPIO Driven
Events – #GPIO ................................................... 79
Enable/Disable GPGGA Message – #GPSGPGGA . 83
Enable/Disable GPGLL Message – #GPSGPGLL ... 84
Enable/Disable GPGSA Message – #GPSGPGSA .. 84
Enable/Disable GPGSV Message – #GPSGPGSV .. 84
Enable/Disable GPRMC Message – #GPSGPRMC 84
Enable/Disable GPVTG Message – #GPSGPVTG .. 85
Enable/Disable Roaming – #WLANROAM ............... 61
Enter FTP Mode – ##FTPMODE ............................. 28
Enter FTP Server Port – #FTPPORT ....................... 28
Erase Flash Memory Parameter Values – #DELFLASH
............................................................................. 13
Error Codes .............................................................. 95
Escape Sequence – S2 ............................................ 51
G
Get Queued GPS Message – #GPSGETMESSAGE85
Give a Domain Name – #IPQUERY ......................... 49
GPS Local Transmission Interval –
#GPSINTERVALLOC ........................................... 85
I
I – Identification ........................................................ 10
id parameter ............................................................. 32
Identification – I ........................................................ 10
Inactivity Timer – #PHYTIMEOUT ............................ 70
Initiate the UDP Session in Listen Mode –
#LUDPSTART ...................................................... 36
Initiate UDP Session in Active Mode – #OUDP........ 37
Internet Connection Number – #DIALSELECT ........ 71
IP Address for Remote PPP – #PPPPEERIP .......... 74
IP Address of PING Request – #PINGREMOTE...... 38
IP Address When Using PPP – #PPPMYIP ............. 74
ISP password – #ISPPW ......................................... 71
ISP User Name – #ISPUN ....................................... 71
Universal IP AT Commands Reference Guide (Document S000457G)
Downloaded from Elcodis.com electronic components distributor
K
Keep Alive Delay – #KEEPALIVEDELAY ................ 68
Keep Alive Mode – #KEEPALIVEMODE ................. 68
Keepalive Port Number – #KEEPALIVEPORT ........ 68
Keepalive Server Address – #KEEPALIVESERV .... 68
Keys for WAP PSK Security Mode – #WPAPSKKEY61
Keys for WEP128 Security Mode – #WEP128KEY . 61
Keys for WEP64 Security Mode – #WEP64KEY ..... 61
Keys for WPA2 PSK Security Mode – #WPA2PSKKEY
............................................................................. 61
L
Legacy Commands
#VSTATE – Display the Current Status of the Device
Display All AT Parameters – #VALL
Display the Current Status of the Device – #VSTATE
Enable/Disable Boot Message – #BOOTMSG
Enable/Disable Watchdog – #WATCHDOG
Restart the Module – #RESET
Restore Default Factory Settings – &F
Turn Echo ON/OFF – E
Watchdog Timer – #WATCHDOGTIMER
Legacy Mode Enable/Disable – #LEGACYMODE ... 14
Load the WLAN Profile – #WLANPROFILE ............ 59
M
Manual Answer of TCP or UDP – A ......................... 51
Mode of Operation – +WOPEN ............................... 66
Move Module out of Power Save – #WLANACTIVATE
............................................................................. 60
Moves Module into or out of Power Save –
#WLANDOZE= .................................................... 59
N
Number of PING Requests – #PINGNUM ............... 38
Number of Rings – #RINGCOUNT .......................... 70
O
Open a TCP Connection – #OTCP .......................... 34
Open Listening Mode – #LTCPSTART .................... 33
P
PDP Context Identifier – #GPRSCID ....................... 75
PING Delay Time – #PINGDELAY .......................... 38
POP3 Header – #POP3HEADERMODE ................. 25
POP3 Module Parameters – #VPOP3 ..................... 27
Previous Command – A/ .......................................... 51
Primary Dial-Up Number – #DIALN1 ....................... 70
R
Received Signal Strength – #WLANGETRSSI ........ 60
Release a DHCP Address Assigned by the Server –
#IPRELEASE ....................................................... 49
Remote PPP Client Password – #PPPSERVPW .... 75
Renew the DHCP Information from the Server –
#IPRENEW .......................................................... 49
Reset Factory Defaults – &F.................................... 11
Reset Main Processor at a Given Time – #AUTORESET
....................................................................... 13, 15
Index
53
53
53
52
52
52
51
10
53
102