Multitech SocketModem iCell MTSMC-G2-IP At Commands Reference Manual page 101

#PUTMAIL – Send Mail to Recipient with Interactive
Mode .................................................................... 23
#RECiADD – Set Email Address .............................. 20
#REDIALCOUNT – Connection Attempts Allowed ... 69
#REDIALDELAY – Call Retry Delay ......................... 69
#RESET – Reset Main Processor or Internal Modem15
#RINGCOUNT – Number of Rings ........................... 70
#SENDERADDR – Set Sender Address .................. 19
#SENDERNAME – Set Sender Name ..................... 19
#SENDMAILi – Send Mail without Interactive Mode 22
#SMTPAUTH – Authentication ON or OFF .............. 24
#SMTPPORT – Set SMTP Server Port .................... 21
#SMTPPW – Set SMTP Password .......................... 21
#SMTPSERV – Set SMTP Server Address ............. 21
#SMTPUN – Set SMTP User Name ......................... 22
#SUBJi – Set Email Pre-Defined Subject Text ......... 20
#TCPPORT – Set TCP Port for Remote Peer .......... 32
#TCPSERV – Set Address of Remote TCP Server .. 32
#TCPTXDELAY – Time Delay.................................. 33
#TELNET – Start/Stop Telnet Session ..................... 54
#TELNETPASSWORD Note
The module must be reset to put the command into
effect. – Set Telnet Password
#TELNETPORT – Set Telnet Port ............................ 54
#TELNETUSER – Set Telnet User ........................... 54
#UDPPORT – UDP Port Number ............................. 36
#UDPSERV – UDP Server Address ......................... 36
#UDPTXDELAY – Delay before Sending UDP
Datagram .............................................................. 36
#VALL – Display All Parameters ........................ 16, 17
#VAUTODISC – Display Auto Discover Commands 45
#VDNS – Display Configuration of DNS Servers43, 50
#VFTP – Display FTP Parameters ........................... 31
#VIP – View Address Settings ........................... 43, 50
#VMAILi – Display Email Parameters for Respective
Mail ID .................................................................. 24
#VPHY – Display Physical Parameters .................... 77
#VPING – Display PING Parameters ....................... 39
#VPOP3 – POP3 Module Parameters ..................... 27
#VPPP – Display PPP Parameters .......................... 76
#VSMTP – Display SMTP Parameters ..................... 24
#VSTATE – Display Current State of Physical
Connection ........................................................... 15
#VTCP – Display TCP Parameters .......................... 35
#VTELNET – View Telnet Settings .......................... 55
#VUDP – Display UDP Module Configuration .......... 37
#VVERSION – Display Software Version ................. 15
#WEP? – View the Values of WEP Keys ................. 62
#WEP128KEY – Keys for WEP128 Security Mode .. 61
#WEP64KEY – Keys for WEP64 Security Mode ...... 61
#WEPKEYID – Set Default TX Key Index ................ 62
#WLAN? – WLAN Module ........................................ 63
#WLANACTIVATE – Move Module out of Power Save
............................................................................. 60
#WLANASSOCINFO – Display Association Information
............................................................................. 64
#WLANCONNECT – Connect with AP ..................... 58
#WLANCOUNTRYCODE – Country Code ............... 56
#WLANDATARATE – WLAN Transmission Data Rate57
#WLANDISCONNECT – Disconnect with AP .......... 58
#WLANDOZE= – Moves Module into or out of Power
Save ..................................................................... 59
#WLANENABLE – Auto Connect Module with AP ... 58
#WLANGETRSSI – Received Signal Strength ......... 60
#WLANIBSSCHANNEL – Channel for Ad-Hoc Mode58
#WLANNETWORKMODE – WLAN Network Mode . 56
#WLANPOWERSAVE – Enable Power Save at Boot62
#WLANPROFILE – Display the WLAN Profile ......... 63
#WLANPROFILE – Load the WLAN Profile ............. 59
Universal IP AT Commands Reference Guide (Document S000457G)
Downloaded from Elcodis.com electronic components distributor
#WLANPROFILEn=n – Change the WLAN Profile .. 59
#WLANROAM – Enable/Disable Roaming .............. 61
#WLANSCAN – SCAN Wireless Networks .............. 60
#WLANSCANMODE – Scanning Mode ................... 57
#WLANSECURITYMODE – Security Mode of WLAN
Module ................................................................. 56
#WLANSSID – SSID of WLAN ................................ 57
#WLANUSEPROFILE – User Profile ....................... 60
#WPA2PSKKEY – Keys for WPA2 PSK Security Mode
............................................................................. 61
#WPAPSKKEY – Keys for WAP PSK Security Mode61
&
&C – RLSD (DCD) Option ....................................... 11
&D – DTR Option ..................................................... 11
&F – Reset Factory Defaults.................................... 11
&S – DSR On or Off ................................................ 11
&W – Store Factory Defaults to NVM ...................... 12
+
55
+ICF – DTE-DCE Character Framing ...................... 12
+IFC – Set Flow Control .......................................... 12
+IPR – Set Serial Speed .......................................... 13
+WOPEN – Mode of Operation ............................... 66
A
A – Manual Answer of TCP or UDP ......................... 51
Access Point Name – #APNSERV .......................... 75
Access Point Name Password – #APNPW ............. 75
Access Point User Name – #APNUN ...................... 75
Answer Incoming Call – #ACCEPT ......................... 72
Append Data to Server – #FTPAPPEND ................. 31
AT – Command Mode ............................................. 10
Authentication ON or OFF – #SMTPAUTH ............. 24
Authentication Type – #AUTHENT .......................... 66
Auto Connect Module with AP – #WLANENABLE ... 58
Auto Discovery On/Off – #AUTODISC .................... 44
Auto Discovery Port – #AUTODISCPORT .............. 44
Auto Discovery Timer – #AUTODISCTIMER ........... 44
Automatic Answer – S0= ......................................... 49
Automatic Call-Back Wait – #CALLBACKTIMER .... 67
Automatically Connect the PPP Link –
#AUTOCONNECTION ......................................... 73
C
Call Retry Delay – #REDIALDELAY ........................ 69
Caller ID – #CALLSCREENNUM ............................. 67
Change the WLAN Profile – #WLANPROFILEn=n .. 59
Channel for Ad-Hoc Mode – #WLANIBSSCHANNEL58
Close TCP Listening Mode – #LTCPSTOP ............. 33
Close UDP Listening Mode – #LUDPSTOP ............ 37
Command Mode – AT ............................................. 10
Configure the DNS Server – #IPDNSSERV ............ 48
Connect with AP – #WLANCONNECT .................... 58
Connection Attempts Allowed – #REDIALCOUNT .. 69
Country Code – #WLANCOUNTRYCODE .............. 56
D
Default Configuration – Z ......................................... 10
Delay before Sending UDP Datagram –
#UDPTXDELAY ................................................... 36
Disconnect with AP – #WLANDISCONNECT .......... 58
Display All Parameters – #VALL ........................ 16, 17
Index
101