Alarm Register Contents - Omron V1000 User Manual

C.10 MEMOBUS/Modbus Data Table
001DH Motor Overheat (PTC input) (oH3)
001EH Digital Operator Connection (oPr)
001FH EEPROM Write Error (Err)
0020H Motor Overheat (PTC input) (oH4)
0021H MEMOBUS/Modbus Communication Error (CE)
0022H Option Communication Error (bUS)
0025H Control fault (CF)
0027H PROFIBUS-DP Option External Fault (EF0)
0028H PID Feedback Loss (FbL)
0029H Undertorque Detection 1 (UL3)
002AH Undertorque Detection 2 (UL4)
u

Alarm Register Contents

The table below shows the alarm codes that can be read out from MEMOBUS/Modbus register 007FH.
Alarm Code
0001H Undervoltage (Uv)
0002H Overvoltage (ov)
0003H Heatsink Overheat (oH)
0004H Drive Overheat (oH2)
0005H Overtorque 1 (oL3)
0006H Overtorque 2 (oL4)
0007H Run commands input error (EF)
0008H Drive Baseblock (bb)
0009H External Fault 3, input terminal S3 (EF3)
000AH External Fault 4, input terminal S4 (EF4)
000BH External Fault 5, input terminal S5 (EF5)
000CH External Fault 6, input terminal S6 (EF6)
000DH Reserved
000FH Cooling Fan Error (FAN)
0010H Overspeed (oS)
0011H Excessive Speed Deviation (dEv)
0012H PG Disconnected (PGo)
0013H Digital operator connection fault (oPr)
0014H MEMOBUS/Modbus Communication Error (CE)
0015H Option Communication Error (bUS)
0016H Serial Communication Transmission Error (CALL)
374
Table C.5 Alarm Register 007FH Contents
Fault Name
0093H Control Circuit Fault (CPF18)
0094H Control Circuit Fault (CPF19)
0095H Hardware fault at power up (CPF20)
0096H Hardware fault at communication start up (CPF21)
0097H A/D Conversion Fault (CPF22)
0098H PWM Feedback Fault (CPF23)
0099H Drive capacity signal fault (CPF24)
0101H Option compatibility error (oFA00)
0102H Option not properly connected (oFA01)
0104H Option Self-diagnostics Error (oFA03)
0105H Option Flash Write Mode Error (oFA04)
Alarm Code
0017H Motor Overload (oL1)
0018H Drive Overload (oL2)
001AH Option Card External Fault (EF0)
001BH Motor Switch command input during run (rUn)
001DH Serial Communication Transmission Error (CALL)
001EH Undertorque Detection 1 (UL3)
001FH Undertorque Detection 2 (UL4)
0020H MEMOBUS/Modbus Test Mode Fault (SE)
0022H Motor Overheat (oH3)
0027H PID Feedback Loss (FbL)
0028H PID Feedback Loss (FbH)
002AH Drive Disabled (dnE)
002BH PG Disconnected (PGo)
0034H High Current Alarm (HCA)
0039H External Fault (input terminal S1) (EF1)
003AH External Fault (input terminal S2) (EF2)
003BH Safe Disable Input (HbbF)
003CH Safe Disable Input (Hbb)
003DH Mechanical Weakening Detection 1 (oL5)
003EH Mechanical Weakening Detection 2 (UL5)
0049H FDBs Alarm (dWAL)
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
Fault Name