Omron V680 User Manual
V680 series amplifier and antennas, id tags
Hide thumbs
Also See for V680:
- Specifications (2 pages) ,
- User manual (76 pages) ,
- Product manual (44 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Omron V680
Summary of Contents for Omron V680
- Page 1 Cat. No. Z262-E1-02A Amplifi er and Antennas V680-HA63A V680-HS52 V680-HS63 ID Tags V680-D1KP52MT V680-D1KP66T V680-D1KP66MT V680 Series USER’S MANUAL...
- Page 2 • Read and understand this manual before attempting to use the RFID System and use the RFID Sys- tem correctly. • Keep this manual in a safe and accessible location so that it is available for reference when required.
- Page 3 READ AND UNDERSTAND THIS DOCUMENT Introduction Product Overview Section 1 Specifications and Performance Section 2 Communications Specifications Section 3 Installation Section 4 Chemical Resistance Section 5 RFID System V680-HA63A Amplifier V680-HS52 Antenna V680-HS63 Antenna V680-HS65 Antenna V680-D1KP52MT ID Tag V680-D1KP66T...
-
Page 4: Read And Understand This Document
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: •... -
Page 5: Safety Precautions
Safety Precautions Alert Symbols for Safe Use The following symbols are used in this manual to indicate precautions that must be observed to ensure safe use of the V680-HS63, V680-HS52, V680-HS65, V680-HA63A, V680-D1KP66T, V680-D1KP66MT, and V680-D1KP52MT. The precautions provided here contain important safety information. Be sure to observe these precautions. -
Page 6: Regulations And Standards
1999/5/EG. French Par la présente Omron déclare que la RFID Système, V680-HS52 Série, V680-HS63 Série, V680-HS65 Série, V680-HA63A Série sont conforme aux exi- gences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. - Page 7 V680-HS65 This device complies with RSS-Gen of IC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 8 10.Malaysia Amplifier Antenna A011579 V680-HA63A V680-HS52 V680-HS63 If the product is used in Malaysia, a label must be attached on-site to the side of the V680-HA63A. Please consult your OMRON sales representative for details. 11.Philippine Amplifier Antenna ESD-0702996C V680-HA63A V680-HS52 V680-HS63 12.Mexico...
-
Page 9: Precautions For Safe Use
4. Because a cable has a locking mechanism, make sure that it has been locked before using the cable. 5. Do not allow water or pieces of wire to enter from openings in the case. Doing so may cause fire or electric shock. -
Page 10: Precautions For Correct Use
V680-HS63: 1.2 N m V680-HS52: 40 N m V680-HS65: 1.2 N m • Transmission will not be possible if the front and back panels are mistakenly reversed and the Unit is mounted to a metallic surface. V680-D1KP66MT • The transmission distance will be reduced when the Unit is not mounted to a metallic surface. - Page 11 Introduction 4. Cleaning • Do not clean the Products with paint thinner or the equivalent. Paint thinner or the equivalent will dis- solve the resin materials and case coating. 5. Combination of the Amplifier • Use the V680-D1KP66T, V680-D1KP66MT, and V680-D1KP52MT ID Tags in combination with only the V680-HA63A Amplifier.
-
Page 12: Meanings Of Symbols
Introduction Meanings of Symbols Indicates particularly important points related to a function, including precautions and application advice. Indicates page numbers containing relevant information. RFID System User's Manual... -
Page 13: Table Of Contents
Precautions for Safe Use Precautions for Correct Use Meanings of Symbols Table of Contents Section 1 Product Overview Features Product Configuration Section 2 Specifications and Performance Antennas with Separate Amplifier Amplifier Tags Section 3 Communications Specifications Communications Distances TAT and Communication Time (Reference) - Page 14 Introduction MEMO RFID System User's Manual...
-
Page 15: Section 1 Product Overview
Section 1 Product Overview Features Product Configuration RFID System User's Manual... -
Page 16: Features
Long Service Life of 100,000 Data Rewrites at Normal Temperatures When the Tag is used at temperatures of up to 25 C, each block of EEPROM data can be rewritten up to 100,000 times. -
Page 17: Product Configuration
Section 1 Product Overview Product Configuration A V680-series RFID System consists of an ID Controller, one or more Amplifiers, one or two Antennas, and Tags. Select the models suitable for the application. Personal computer Programmable Controller (PLC) RS-232C RS-422 RS-485... - Page 18 Section 1 Product Overview MEMO RFID System User's Manual...
-
Page 19: Section 2 Specifications And Performance
Section 2 Specifications and Performance Antennas with Separate Amplifier Amplifier Tags RFID System User's Manual... -
Page 20: Antennas With Separate Amplifier
Ambient operating 35% to 95% (with no condensation) humidity Insulation resistance 20 M min. (at 500 VDC) between cable terminals and case Dielectric strength 1,000 VAC, 50/60Hz for 1 min between cable terminals and case Degree of protection IP67.(IEC60529) IP67.(IEC60529) - Page 21 (Unit: mm) Connector (39.5) Insulation cover Coaxial cable, 5.3 dia., standard length: 2 m Operation indicator Note: Mounting Hole Dimensions Two, M4 or 4.5 dia. holes Coil center Case material ABS resin Fill resin Epoxy resin Cable PVC (black) RFID System...
-
Page 22: General Specifications
Ambient operating humidity Insulation resistance 20 M min. (at 500 VDC) between connector terminals and case Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and case Degree of protection IP67.(IEC60529) IP67.(IEC60529) In-house standard for antenna oil resistance... - Page 23 Two lock nuts Mounting Hole Dimensions Ferrite core Operation indicator Insulation cover Antenna Connector 35 dia. (39.5) 47.6 Insulation cover Coaxial cable, 5.3 dia., standard length: 2 m Case material Brass Communications ABS resin surface Fill resin Epoxy resin Cable PVC (black)
- Page 24 20 M min. (at 500 VDC) between connector terminals and case Insulation resistance Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between connector terminals and case Degree of protection IP67 (IEC60529) IP67 (IEC60529) In-house standard for antenna oil resistance...
- Page 25 (Unit: mm) 90 0.2 4-4.5 dia. Operation indicator (Mounting holes) Ferrite core Connector (39.5) Bushing Insulation cover Coaxial cable, 5.3 dia., standard length: 2 m Case material ABS resin Fill resin Epoxy resin Cable PVC (black) RFID System User's Manual...
-
Page 26: Amplifier
Approx. 650 g (with 10 m cable) Cable length Standard lengths of 5 and 10 m Note: The maximum total cable extension is 50 m (including the Amplifier cable). A maximum of two extension cables can be connected. Dimensions Operation indicator 13.7... - Page 27 RUN mode to conduct a sufficient number of tests in the actual operating environment. Values of distance level 4 or above may not be displayed, but this will not affect the RUN mode performance and does not indicate a malfunction.
-
Page 28: Specifications
Section 2 Specifications and Performance Cables Specifications Item Model V700-A43/V700-A44 Number of conductors 10 Insulation resistance 5 M min. (at 500 VDC) between terminals and sheath Dielectric strength 500 VAC, 1 min Dimensions Item Model V700-A43 V700-A44 Length (L1) Approx.10m Approx. -
Page 29: Tags
When embedding the V680-D1KP52MT into a metal surface, use the V680-HS52 Antenna. Transmission will not be possible if the V680-HS63 Antenna is used. The side with the markings is the communications surface. Mount the Tag with this side facing the Antenna. RFID System... - Page 30 D1KP66MT markings are shown in the following diagrams. V680-D1KP66MT V680-D1KP66T V680-D1KP66MT V680-D1KP66T XXXXXX XXXXXX MADE IN JAPAN MADE IN JAPAN The side with the markings is the communications surface. Mount the Tag with this side facing the Antenna. RFID System User's Manual...
- Page 31 • Storing Tags under high temperatures will adversely affect the performance of the internal parts and the service life of the Tags. • An LTPD of 10% was determined during the evaluation for Tags that reached the end of their life after testing under the following test conditions.
-
Page 32: Memory Map
1 byte EEPROM is used as memory in the Tags. The memory capacity available to the user is 1,000 bytes, including 0000H to 0003H (the Write Protec- tion Setting Area). The access to the memory is executed at every block. - Page 33 After important data has been written to memory, it can be write-protected using the following method. The write protect function setting can be switched with switches 4 to 7 (Write Protect Function Setting) of the V680- CA5D @@ -V2 Controller.
- Page 34 Section 2 Specifications and Performance MEMO RFID System User's Manual...
-
Page 35: Section 3 Communications Specifications
Section 3 Communications Specifications Communications Distances TAT and Communication Time (Reference) RFID System User's Manual... -
Page 36: Communications Distances
0 to 12.0 mm (Axis offset: 2) V680-HS63 V680-D1KP52MT Write 0 to 9.5 mm (Axis offset: 2) When embedding the V680-D1KP52MT into a metal surface, use the V680-HS52 Antenna. Transmission will not be possible if the V680-HS63 Antenna is used. • Measurement Conditions V680-D1KP52MT Metal... - Page 37 Section 3 Communications Specifications Communications Area (Reference) V680-HS52 & V680-D1KP52MT V680-HS52 & V680-D1KP52MT Embedded in Metal (Steel) Read Read Write Write X Axis X Axis (Unit: mm) (Unit: mm) V680-HS63 & V680-D1KP52MT Read Write X Axis (Unit: mm) RFID System...
- Page 38 Communications Specifications V680-D1KP66T Communications Distance Specifications (Certified Performance) Amplifier Antenna ID Tag Communications distance Read 0 to 17.0 mm (Axis offset: 2) V680-HS52 V680-D1KP66T Write 0 to 17.0 mm (Axis offset: 2) Read 0 to 30.0 mm (Axis offset: 10) V680-HA63A...
- Page 39 Section 3 Communications Specifications Communications Area (Reference) V680-HS52 and V680-D1KP66T V680-HS63 and V680-D1KP66T Read Read Write Write 10 0 10 0 (Unit: mm) (Unit: mm) V680-HS65 and V680-D1KP66T Read Write 100 80 20 0 (Unit: mm) RFID System User's Manual...
- Page 40 V680-D1KP66MT Communications Distance Specifications (Certified Performance) Amplifier Antenna ID Tag Communications Distance Read 0 to 16.0 mm (Axis offset: 2) V680-D1KP66MT V680-HS52 with metal on back surface (steel) Write 0 to 14.0 mm (Axis offset: 2) Read 0 to 25.0 mm (Axis offset: 10)
- Page 41 Section 3 Communications Specifications Communications Area (Reference) V680-HS52 and V680-D1KP66MT V680-HS63 and V680-D1KP66MT with Metal on Back Surface (Steel) with Metal on Back Surface (Steel) Read Read Write Write 10 0 10 0 (Unit: mm) (Unit: mm) V680-HS65 and V680-D1KP66MT...
-
Page 42: Tat And Communication Time (Reference)
T = 1.8 N + 51 Write (without verification) T = 1.5 N + 47 Note: When using multi-access or FIFO communications options, normal-mode communications speed will be used regardless of the high-speed mode setting. Communications speed: Normal mode Communications speed: high-speed mode... - Page 43 Communications Specifications TAT (Turn Around Time) “ TAT” is the total time from the start of command transmission by the host device (e.g., a personal computer) until a response is received by the host device. Command transmission time Tag communications time...
- Page 44 Note 1. When using multi-access or FIFO communications options, normal-mode communications speed will be used regardless of the high-speed mode setting. 2. TAT data is for a V680-CA5D01/02-V2 ID Controller with the following communications settings: 8-bit data length, 1 stop bit, and odd parity. Data was sent continuously without breaks between characters.
- Page 45 Note 1. The distance travelled in the communications area depends on the read/write distance and the axis offset. Refer to the diagrams in Communications Area. 2. The speed of the Tag is provided as a guideline. Before using the RFID System, run a test to determine the speed under actual operating conditions.
- Page 46 Section 3 Communications Specifications MEMO RFID System User's Manual...
-
Page 47: Section 4 Installation
Section 4 Installation Installing Antennas Mounting Amplifiers Installing Tags RFID System User's Manual... -
Page 48: Installing Antennas
When the Antenna is mounted to a metal object, the communications distance will be reduced by approximately 10% compared with mounting to a non-metallic object. For details on the effect of metal surrounding the Antenna, refer to Effect of Surrounding Metals on the Antenna (Reference) on page 48. - Page 49 Tighten the screws to a torque of 0.7 to 1.2 N m. There are no restrictions on the mounting direction or the direction of access to the Tag, but if the Antenna is to be installed near a device such as a conveyance belt, make sure there is no danger of the Antenna being 90±0.2...
- Page 50 To prevent malfunctioning, allow a space of at least 30 mm between the Antenna and the sides of the metal casing. If the space is less than 30 mm, the read/write distance will be greatly diminished. In addition, the height of metal casing must not exceed that of the Antenna.
- Page 51 To prevent malfunctioning, allow a space of at least 100 mm between the Antenna and the sides of the metal casing. If the space is less than 100 mm, the read/ write distance will be greatly diminished. In addition, the height of metal casing must not exceed that of the Antenna.
- Page 52 Section 4 Installation Mutual Interference between Antennas (Reference) To prevent malfunctioning due to mutual interference when using more than one Antenna, leave suffi- cient space between them as shown in the following diagrams. V680-HS63 • Installing the Antennas Facing Each Other •...
-
Page 53: Mounting Amplifiers
10 mm min. (See note 2.) Mounting hook Note 1. Consider the height of the DIN Track. 2. Provide a space of at least 10 mm (i.e., at least two spacers) and attach them securely. Spacer DIN Track End Plate... - Page 54 Antenna connector The connector will not come out unless the lock is first released by turning the connector. To remove the cable, release the lock and pull on the connector. Pulling the cable without releasing the lock may break or damage the cable.
-
Page 55: Installing Tags
When embedding the V680-D1KP52MT into a metal surface, use the V680-HS52 Antenna. Transmission will not be possible if the V680-HS63 Antenna is used. Differences in Surrounding Metals Communications distances are affected by the type of metal in back of or surrounding the Tag, as shown in the following table. Steel... - Page 56 Install Antennas and Tags as close to parallel to each other as possible. Communications are possible even when an Antenna and a Tag are mounted at an angle, but the communications distance will be shortened. The relation between the angle and the communications distance is shown below.
- Page 57 The V680-D1KP66T communications distance is reduced if there is any metal material behind the Tag. If the Tag is to be mounted to metal, then either use a V600-A86 Attachment (sold separately) or insert a non-metal spacer (such as plastic or resin). The relationship between the distance from the Tag to the metal surface and the communications distance is shown below.
- Page 58 Install Antennas and Tags as close to parallel to each other as possible. Communications are possible even when an Antenna and a Tag are mounted at an angle, but the communications distance will be shortened. The relation between the angle and the communications distance is shown below.
- Page 59 25 0.2 25 0.2 Effect of Surrounding Metals The V680-D1KP66MT can be surface-mounted or it can be embedded in metal. If it is embedded in metal, the height of the metal casing must not exceed that of the Tag. Embedded Surface-mounted 3.5 mm max.
- Page 60 Install Antennas and Tags as close to parallel to each other as possible. Communications are possible even when an Antenna and a Tag are mounted at an angle, but the communications distance will be shortened. The relation between the angle and the communications distance is shown below.
-
Page 61: Section 5 Chemical Resistance
Section 5 Chemical Resistance Chemical Resistance of the Antennas Chemical Resistance of Tags Degree of Protection RFID System User's Manual... -
Page 62: Chemical Resistance Of The Antennas
V680-HS63-W/R V680-HS52-W/R V680-HS65-W/R ABS resin is used for case material and epoxy resin for filling material. Refer to the following lists and do not use chemicals that affect ABS and epoxy resin. Chemicals That Cause Deformations, Cracks, Etc. ABS resin... -
Page 63: Chemical Resistance Of Tags
A: Has no adverse effect, B: May cause discoloration, swelling, etc., C: Causes deformation, cracks, etc. The above table shows the extent of changes in PPS resin exposed to each chemical at room temperature and at 90 C. If actual chemicals, concentrations, and temperatures are different from those shown in the tables, always conduct tests under the actual conditions in which the Tags are to be used. - Page 64 Applicable Model V680-D1KP52MT PPS resin is used for case material and epoxy resin for filling material. Refer to the following lists and do not use chemicals that affect PPS and epoxy resin. Tags cannot be used in applications with explosion-proof specifications.
-
Page 65: Degree Of Protection
Degree No protection Protects against penetration of any solid object such as a hand that is 50 mm or more in diameter. 50 mm dia. Protects against penetration of any solid object, such as a finger, that is 12.5 mm or more in diame- 12.5 mm dia. - Page 66 No adverse affect from oil drops or oil spray approaching from any direction. Oil-proof Protects against penetration of oil drops or oil spray approaching from any direction. Note: This OMRON in-house standard confirms resistance to cutting and other oils. It is equivalent to the former JEM standard. RFID System...
- Page 67 Section 5 Chemical Resistance MEMO RFID System User's Manual...
-
Page 68: Revision History
Revision History A manual revision code appears as a suffix to the catalog number at the bottom of the front and rear pages. Cat. No.: Z262-E1-02A Revision code Revision code Date Revised contents May 2007 Original production July 2007 Added item for V680-HS65 Antenna, and the overseas regulations and standards.