Omron V1000 User Manual page 310

No. Name
Max Output
E1-04
Frequency
E1-05
Max Output
These parameters are only applicable when E1-03 is set to
<24>
Voltage
F. To set linear V/f characteristics, set the same values for
E1-07 and E1-09. In this case, the setting for E1-08 will be
E1-06 Base Frequency
disregarded. Ensure that the four frequencies are set
according to these rules:
Mid Output
E1-07
E1-04 ≥ E1-06> E1-07 ≥ E1-09
Frequency
E1-08
Mid Output
<24> Frequency Voltage
Minimum Output
E1-09
Freq.
E1-10
Minimum Output
<24>
Freq. Voltage
E1-11
Mid Output
<26>
Frequency 2
E1-12
Mid Output
<24>
Frequency Voltage
<26> 2
E1-13
Base Voltage
<24>
Motor Rated Sets the motor nameplate full load current in amperes (A).
E2-01
Current Automatically set during Auto-Tuning.
Sets the motor rated slip in Hertz.
E2-02 Motor Rated Slip
Automatically set during rotational Auto-Tuning.
Motor No-Load Sets the magnetizing current of the motor in Ampere.
E2-03
Current Automatically set during rotational Auto-Tuning.
Number of Motor Sets the number of motor poles. Automatically set during
E2-04
Poles Auto-Tuning.
Motor Line-to-Line Sets the phase-to-phase motor resistance in ohms.
E2-05
Resistance Automatically set during Auto-Tuning.
Sets the voltage drop due to motor leakage inductance as a
Motor Leakage
E2-06 percentage of motor rated voltage.
Inductance
Automatically set during Auto-Tuning.
Motor Iron-Core
Sets the motor iron saturation coefficient at 50% of
E2-07 Saturation
magnetic flux. Automatically set during Auto-Tuning.
Coefficient 1
Motor Iron-Core
Sets the motor iron saturation coefficient at 75% of
E2-08 Saturation
magnetic flux. Automatically set during Auto-Tuning.
Coefficient 2
Sets the motor mechanical loss as a percentage of motor
rated power (kW). Adjust in the following circumstances:
Motor Mechanical
E2-09 When there is a large amount of torque loss due to motor
Loss
bearing friction.
When there is a large amount of torque loss.
Motor Iron Loss for
E2-10 Torque Sets the motor iron loss in watts (W).
Compensation
Sets the motor rated power in kilowatts (kW).
E2-11 Motor Rated Output
Automatically set during Auto-Tuning. (1 HP = 0.746 kW).
Motor Iron-Core Set to the motor iron saturation coefficient at 130% of
E2-12 Saturation magnetic flux.
Coefficient 3 Automatically set during rotational Auto-Tuning.
Motor 2 Control 0: V/f Control
E3-01
Method 2: Open Loop Vector (OLV)
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
Description
VACrms Out(V)
E1-05
E1-12
E1-13
E1-08
E1-10
E1-09 E1-07 E1-06 E1-11 E1-04
Frequency (Hz)
E2: Motor Parameters
Use E2 parameters to set motor-related data.
E3: Motor 2 V/f Characteristics
Use E3 parameters to set the V/f pattern for a second motor.
B.2 Parameter Table
Control
Mode
Range Def.
OL
V/f
V
40.0 to
50 Hz
400.0
S S
<10>
<21>
200 V
0.0 to 255.0 S S
<10>
50 Hz
0.0 to
S S
<10>
E1-04
2.5 Hz
0.0 to
A A
<2>
E1-04
16.0 V
0.0 to 255.0 A A
<2> <12>
1.3 Hz
0.0 to
S S
<2> <10>
E1-04
12.0 V
0.0 to 255.0 A A
<2> <12>
0.0 to
0.0 Hz A A
E1-04
0.0 to 255.0 0.0 V A A
0.0 to 255.0 0.0 V A S
10 to 200%
of drive
rated <57>
S S
current
<27>
0.00 to
<57>
A A
20.00
0 to less
<57>
A A
than E2-01
2 to 48 4 poles A A
0.000 to
65.000 <57>
A A
<37>
<57>
0.0 to 40.0 A A
E2-07 to
0.50 − A
0.50
E2-07 to
0.75 − A
0.75
0.0 to 10.0 0.0% − A
0 to 65535 <57> A −
0.40 kW
0.00 to
S S
<12>
650.00
1.30 to 5.00 1.30 − A
0 or 2 0 A A
Addr. Hex Pg.
PM
S 303 146
S 304 146
S 305 146
- 306 146
- 307 146
S 308 146
- 309 146
- 30A 146
- 30B 146
- 30C 146
− 30E 147
− 30F 147
− 310 147
− 311 148
− 312 148
− 313 148
− 314 148
− 315 148
− 316 148
− 317 148
− 318 149
− 328 149
− 319 149
B
309