Omron V1000 User Manual page 312

No. Name
Enter the Yaskawa motor code for the PM motor being
used. Various motor parameters are automatically set based
on the value of this parameter.
Note: Set to FFFF when using a specialized or custom
motor. For all other motors:
Motor Code
E5-01
Selection (for PM
<25>
motor)
All motor parameters are reinitialized to factory settings
when this parameter is set.
Motor Rated
E5-02
Capacity (for PM Sets the rated capacity of the motor.
<25>
motor)
E5-03
Motor Rated
Sets the motor rated current in amps.
<25>
Current
E5-04
Motor Poles Sets the number of motor poles.
<25>
E5-05
Set the resistance for each motor phase in units of
Motor Resistance
<25>
0.001 Ω.
E5-06
Motor d Axis
Sets the d axis inductance in units of 0.01 mH.
<25>
Inductance
E5-07
Motor q Axis
Sets the q axis inductance in units of 0.01 mH.
<25>
Inductance
Set the induced phase peak voltage in units of 0.1 mV (rad/
s) [electrical angle].
Set this parameter when using a Yaskawa SSR1 series PM
E5-09
Motor Induction motor with derate torque, or a Yaskawa SST4 series motor
<25>
Voltage Constant 1 with constant torque.
When setting this parameter, E5-24 should be set to 0. An
alarm will be triggered if both E5-09 and E5-24 are set to
0, or if neither parameter is set to 0.
Set the induced phase-to-phase rms voltage in units of 0.1
mV/(r/min) [mechanical angle].
Set this parameter when using a Yaskawa SMRA Series
SPM Motor.
E5-24
Motor Induction When setting this parameter, E5-09 should be set to 0. An
<25>
Voltage Constant 2 alarm will be triggered if both E5-09 and E5-24 are set to
0, or if neither parameter is set to 0.
If E5-03 (Motor Rated Current) is set to 0, however, then
an alarm will not be triggered when both E5-09 and E5-24
are set to 0.
<2> Default setting value is dependent on parameter A1-02, Control Method Selection. The value shown is for A1-02 = 0-V/f Control.
<4> Default setting value is dependent on parameter A1-06. This setting value is 0 when A1-06 = 0, and 1 when A1-06 does not = 0.
<10> Default setting value is dependent on parameter E5-01, Motor Code Selection.
<12> Default setting value is dependent on parameter o2-04, Drive Model Selection.
<21> Range upper limit is dependent on parameter E4-01 Motor 2 Rated Current.
<22> Parameter can be changed during run.
<24> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<25> Parameter setting value is not reset to the default value during drive initialization, A1-03 = 1110, 2220, 3330.
<26> Parameter ignored when E1-11, Motor 1 Mid Output Frequency 2, and E1-12, Motor 1 Mid Output Frequency Voltage 2, are set to 0.0.
<27> Setting units for this parameter are determined by o2-04, Drive Model Selection. Less than 11 kW: 2 decimal points, 11 kW and above: 1
decimal point.
<37> Setting range becomes 0.00 to 130.00 for drives 0.2 kW and smaller.
<38> If using a Yaskawa SMRA Series SPM Motor, the default setting is 1800 r/min.
<52> Parameter ignored when E3-11, Motor 2 Mid Output Frequency 2, and E3-12, Motor 2 Mid Output Frequency Voltage 2, are set to 0.
<53> Default setting depends on the control mode for motor 2 set in parameter E3-01. The given value is for V/f Control.
<57> Default setting value is dependent on parameter o2-04, Drive Model Selection and C6-01, Drive Duty Selection.
SIEP C710606 20 OYMC AC Drive - V1000 User Manual
Description
E5: PM Motor Parameters
0 0 0 0
Motor Voltage Class
and Capacity
0: 1800 r/min Series
0: Pico Motor
1: 3600 r/min Series
(SMRA Series)
2: 1750 r/min Series
1: Derated Torque for IPM
3: 1450 r/min Series
Motors
4: 1150 r/min Series
(SSR 1 Series)
F: Special Motor
B.2 Parameter Table
Control
Mode
Range Def.
OL
V/f
V
<12>
0000 to
− −
FFFF <38>
0.10 to 18.5 <10> − −
10 to 200%
of drive
rated <4>
− −
current
<27>
<10>
2 to 48 − −
0.000 to
<10>
− −
65.000
0.00 to
<10>
− −
300.00
0.00 to
<10>
− −
600.00
0.0 to
<10> − −
2000.0
0
0.0 to
− −
<10>
2000.0
Addr. Hex Pg.
PM
S 329 152
S 32A 152
S 32B 152
S 32C 152
S 32D 153
S 32E 153
S 32F 153
S 331 153
S 353 153
B
311