Async Terminal Operation - Paradyne 3150 Operator's Manual

Async Terminal Operation

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before Using the Async Terminal
Initiating an Async Terminal Session
Ending an Async Terminal Session
Menu Organization
Using Async Terminal Screens
Setting Customer Identification
Displaying LED Conditions
Changing Configuration Options
Displaying or Editing Configuration Options
Saving Edit Changes
Establishing Access Security on a Port
Setting a Password
Entering a Password to Gain Access
Configuration Worksheets for the Async Terminal Interface
Overview
You can configure and manage the CSU from an
asynchronous (async) terminal that is configured for
9.6 kbps, 8 characters, no parity, and 1 stop bit.
This appendix provides operational examples to help
you become familiar with the use of the async terminal for
CSU control.
By convention throughout this appendix, examples of
screens are shown as they appear with the standalone
CSU.
Before Using the Async
Terminal
You can connect the async terminal directly to the
COM port of the CSU, or you can establish a remote
connection using dial-in (via the integral modem) or
Telnet access.
3150-A2-GB21-80
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
February 1998
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before using the async terminal, you may use the
CSU's front panel to set certain configuration options for
async terminal operation. Use the Configuration (Cnfig)
branch of the front panel menu and edit the User Interface
(User) configuration options for async terminal operation.
Refer to the Changing Configuration Options
Chapter 3, Operation, and Appendix C,
Options.
To connect the async terminal to the CSU using Telnet
access, refer to the Configuring the CSU for SNMP or
Telnet Access section in Chapter 3, Operation.
If the CSU is misconfigured, leaving it in a state that
does not support async terminal operation, the recovery
procedure consists of power cycling the CSU, waiting for
the completion of the power-up self-test, and then
pressing the async terminal's Return key five times in
succession. (Begin pressing the Return key within two
seconds after the completion of power-up self-test, and do
not wait longer than one second between each successive
key press.) This procedure allows you to use the System
Paused screen to reset the COM port configuration
options or to reload all factory default configuration
options.
H
H-1
H-1
H-2
H-2
H-3
H-4
H-5
H-6
H-7
H-7
H-9
H-10
H-11
H-12
H-13
section in
Configuration
H-1