Page 1
AREA CODE CHANGE Please note that the area code for Paradyne Corporation in Largo, Florida has changed from 813 to 727. For any Paradyne telephone number that appears in this manual with an 813 area code, dial 727 instead.
Page 3
Copyright 1997 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Avenue North, P.O.
August 1997 Quick Start Procedure The following procedure is for experienced CSU users who are familiar with the 3151 CSU installation process and have no special requirements for their application. See the ACCULINK 315x Channel Service Unit Operator’s Guide (3150-A2-GB21) for more information.
Page 5
2. Attach the DTE cable (DB15) to the appropriate DTE connector on the Auxiliary Backplane. (See the COMSPHERE 3000 Series Carrier Installation Manual (3000-A2-GA31) for detailed cable and connector information.) Connect the other end of the DTE cable to the customer premises equipment. 3.
Page 6
5. Insert the CSU circuit card into the appropriate slot in the carrier. The power-up self-test begins. 6. If you intend to use front panel emulation, connect the cable from the PC to Port 2 on the Auxiliary Backplane using the COM port adapter and COM-port-to-PC cable. 7.
Page 9
Table 2. Network Interface Configuration Options (2 of 2) Option Factory 1 Enab NET LLB: NET LLB: Disab Enab NET PLB: NET PLB: Disab BitStuff: One (Framed All Ones) KeepAlive: KeepAlive: NetLp (Loopback of network signal) Enab Yellow: Yellow: Disab Edit Circuit Ident: Circuit Ident:...
Page 10
Table 4. User Interface Configuration Options (1 of 3) Option Factory 1 Enab Self-Test: Self-Test: Disab Enab Dial-In: Dial-In: Disab Enab Com Port: Com Port: Disab Mgmt ASCII Com Use: Term Disab ComExtDev: Other Edit ComConnPrefix: ComConnPrefix: Clear Edit ComConnected: ComConnected: Clear Edit...
Page 11
Table 4. User Interface Configuration Options (2 of 3) Option Factory 1 Com Rate: (Communication Port (Communication Port Rate) a e) 14.4 19.2 Char Length: Char Length: None CParity: CParity: Even (Communication Port Parity) Parity) CStop Bits: CStop Bits: (Communication Port Stop Bits) Stop Bits) Ignore DTR:...
Page 12
Table 4. User Interface Configuration Options (3 of 3) Option Factory 1 TnDiscTm: (Telnet TnDiscTm: (Telnet Disconnect Time) t Ti Down Save Table 5. Alarm Configuration Options Option Factory 1 Disab Alrm Msg: Alrm Msg: Enab SNMP Trap: SNMP Trap: Disab Enab TrapDisc:...
Page 13
Table 6. General Management Configuration Options (1 of 2) Option Factory 1 Disab SNMP Mgt: SNMP Mgt: Enab Disab NMS Valid: NMS Valid: Enab Num Sec Mgrs: Num Sec Mgrs: 2–10 Edit NMS n IP Adr: NMS n IP Adr: Clear Read NMS n Access:...
Page 14
Table 6. General Management Configuration Options (2 of 2) Option Factory 1 Edit Com NetMask: Com NetMask: Clear Com Link: Com Link: SLIP Enable IPBusMast: IPBusMast: Disab None IPBus Def Netwk: EDL n Table 7. Management Trap Configuration Options (1 of 2) Option Factory 1 Num Trap Mgrs:...
Page 15
Table 7. Management Trap Configuration Options (2 of 2) Option Factory 1 Enab Entp Trap: Entp Trap: Disab Disab Link Trap: Link Trap: Down Both Trap I/F: Trap I/F: Ports Factory 2 Comments/Description Enab Specifies whether the EnterpriseSpecific trap type is EnterpriseSpecific trap type is Disab enabled.