Table of Contents
Advertisement
Rear Panel Features
PowerCage 411 Rear Panel
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort. L'installation
A A A
100-240V ~ --A MAX
100-240V ~ --A MAX
USB HID
USB 2.0
AUDIO IN
RS-232
Tx
Rx G
50-60 Hz
50-60 Hz
Figure 3.
A
B
C
D
WARNING:
Potential risk of severe injury. Installation and service must be
performed by authorized personnel only.
et l'entretien doivent être effectués par le personnel autorisé uniquement.
A
B
A
OUT IN OUT IN
N
OUT I
OUT IN OUT IN
UT
UT
U T
UT
U
T
T
T
OUT I
UT
UT
UT
T
T
T
USB HID
USB 2.0
AUDIO IN
RS-232
HDMI INPUT
LOOP OUT
Tx
Rx G
HDMI INPUT
Rear Panel of the PowerCage 411 Enclosure
Power inlets — Connect 110-240 VAC, 50-60 Hz power sources using standard IEC
power cords to these inlets.
NOTE: The power supplies and transmitter boards may be installed or replaced
before or after the unit is powered on.
Slot 1 through slot 4 — Install a PowerCage 411 compatible board into each slot as
Installing the Transmitter Boards into the Enclosure
needed (see
LAN port — Use an RJ-45 cable to connect this port to a LAN (Ethernet) for control of
the device.
Wire the connector as shown in figure 4.
Pins:
12345678
(for connection to a switch, hub, or router)
Pin
1
2
RJ-45
3
Connector
4
5
6
Insert Twisted
7
Pair Wires
8
TIA/EIA-T568B
Figure 4.
LAN Port Wiring Diagram
Remote RS-232 port — To
control the unit, connect an
RS-232 device to the 3-pole,
3.5 mm captive screw port
and configure it as follows:
9600 baud rate, 8 data bits,
1 stop bit, no parity. Wire the
connector as shown in the
image on the right.
NOTE: The LAN port and RS-232 port allow communication to the enclosure and
the boards (see
RS-232 Insertion
B B B
B
A
B
N
OUT IN OUT IN
OUT I
UT
U
U T
N
USB HID
USB 2.0
AUDIO IN
RS-232
Tx
LOOP OUT
Rx G
HDMI INPUT
LOOP OUT
Straight-through Cable
End 1
End 2
Wire Color
Pin
Wire Color
white-orange
1
white-orange
orange
2
orange
white-green
3
white-green
blue
4
blue
white-blue
5
white-blue
green
6
green
white-brown
7
white-brown
brown
8
brown
T568B
RS-232
Tx Rx G
Do not tin the wires!
Ground (G)
Receive (Rx)
Transmit (Tx)
on page 19).
PowerCage 411 Series • Installation
A
B
OUT I
OUT IN OUT IN
UT
UT
UT
T
T
T
N
USB HID
USB 2.0
AUDIO IN
RS-232
Tx
Rx G
HDMI INPUT
LOOP OUT
on page 13).
Crossover Cable
(for direct connection to a PC)
End 1
End 2
Pin
Wire Color
Pin
Wire Color
1
white-orange
1
white-green
2
orange
2
green
3
white-green
3
white-orange
4
blue
4
blue
5
white-blue
5
white-blue
6
green
6
orange
7
white-brown
7
white-brown
8
brown
8
brown
T568B
T568A
Controlling
Device
Bidirectional
Ground (G)
Receive (Rx)
Transmit (Tx)
C C C D D D
10
Advertisement
Table of Contents
