Extron electronics PowerCage 411 Series User Manual page 50

Command
FOX3 PC Transmitter Commands Continued
HDCP authorized device
Set HDCP authorized device on
Set HDCP authorized device off
View HDCP authorized device
X5!
KEY: = Input HDCP Authorization
Input audio selection
Select audio input
View selected audio input
X4*
= Input audio selection
KEY:
Input signal detection information
View detected input signal
information
X5%
KEY: = Resolution and refresh rate
X5^
= Detected input audio format
X5&
= Detected video input color space 0 = Not detected
X5*
= Pixel clock (in MHz)
Force 4K60 compressed mode
Force 4K 60 compressed mode
Disable 4K 60 comressed mode
View 4K 60 compressed mode
status
This command on
NOTE:
issued to the wrong unit, return E14.
X5@
= Force 4K60 compressed mode 0 = Disable (default; after a reset defaults back to 0)
KEY:
Information requests
View firmware version
View full firmware version
View part number
View Extron serial number
View updated FPGA version
View LinkLicense
ASCII Command
(host to PowerCage)
E
}
E0HDCP
E
}
EHDCP
Verbose mode 2/3
0 = HDCP authorized off
E X4*
}
I AFMT
E
IAFMT }
0 = Auto (default)
35I/i
Verbose mode 2/3
nnnn
Horizontal
0 = Not detected
4-digit response with 0 padding (example: 297 = 0297MHZ
E
C1FOXM }
E
C0FOXM }
E
CFOXM }
Verbose mode 2/3
ly applies to devices with the 4K60 Uncompressed Video LinkLicense or -13/-14 transmitter units. If the command is
Q/q
Verbose mode 2/3
*Q/q
Verbose mode 2/3
N/n
Verbose mode 2/3
19I/i
Verbose mode 2/3
35Q/q
Verbose mode 2/3
E
}
LELIC
Response
(PowerCage to host)
]
HdcpE1
]
HdcpE0
X5!
]
X5!
]
HdcpE
1 = HDCP authorized on (default)
X4*
]
AfmtI
X4*
]
1 = Digital
X5% X5^ X5&
Res •AudI •VcsI •Pixcl
X5% X5^
Inf35* Res
•AudI •VcsI
@ xxHz (
xnnnn x @
Vertical 0000 0000
1 = Digital
1 = YUV
]
FoxmC1
]
FoxmC0
X5@
]
X5@
]
FoxmC
x.xx ]
x.xx ]
Ver 01*
]
x.xx.xxxx
]
Bld x.xx.xxxx
]
60-xxxx-xx
]
Pno 60-xxxx-xx
]
Serial number
]
Inf19*Serial number
x.xx ]
x.xx ]
Ver 35*
FOX3 Uncomprompressed Video, 79-2560-01
If LinkLicense is not installed, returns
PowerCage 411 Series • SIS Configuration and Control
Additional Description
Default: HDCP authorized on.
Default is Auto, with Digital as priority.
2 = Analog
X5*
]
X5& X5*
]
•Pixcl
Hz = no input detected)
000
2 = Analog
2 = RGB
(0000 = Not detected)
)
Sends 4K60 signal compressed on 1 fiber
Sends 4K60 signal uncompressed on 2
fibers
1 = Force 4K60 on 1 fiber
]]
]]
42