Table of Contents
Advertisement
5
Adjustment > Adjustment at Time of Parts Replacement > Outline
Adjustment at Time of Parts Replacement
Outline
CAUTION: Setting the Dip Switch
If setting the Dip Switch, the Delivery Tray setting on the host machine side returns to
the default.
After setting the Dip Switch, it is necessary to execute the Delivery Tray setting on the
host machine side again.
Except for some items, the adjustment and setting can input from the both devices of the host
machine (service mode) and the finisher (Dip switch).
The input value is memorized in the EEPROM of finisher controller. Regardless of the input
device (host machine or finisher), the setting range and unit are same, and the final input
value is effective.
Bit setting of DSW1
Item
in the finisher
controller PCB
Bufferless Mode
ON:1, 3, 8
Adjustment in the Case
ON:1, 3, 6, 7
of Failure in Stacking
Performance of Tray
(upper curl)
Adjustment in the Case
ON:1, 3, 6, 7
of Failure in Stacking
Performance of Tray
(lower curl)
Adjustment in the Case
ON:1, 3, 7
of Failure in Stacking
Performance of Tray
(runon of paper when
using thin paper)
Adjustment in the Case
ON:1, 3, 5
of Canceling Limit for
Tray Stack
Setting of Pressless
ON:1, 3, 4
Mode
5
Adjustment > Adjustment at Time of Parts Replacement > Outline
Service mode
Range Default
Reference
SORTER> OPTION
0 to 4
0
p. 5-53
>BUFFSW
SORTER>OPTION
0 to 2
0
p. 5-54
>CURLSW
SORTER>OPTION
0 to 2
0
p. 5-56
>CURLSW
SORTER>OPTION
0 to 1
0
p. 5-58
>TRYEJCT
SORTER>OPTION
0 to 1
0
p. 5-60
>TRYOVER
SORTER>OPTION
0 to 3
0
p. 5-120
>SDLPRS
When replacing the parts shown below, perform the appropriate adjustment.
Adjustment Type
Adjusting Sensor Light
When replacing a sensor
Intensity
Adjusting Position of
When replacing the Tray A/B Unit
Tray A, B
Adjusting the Alignment
When replacing or installing/removing the Neat Stack
Position of the Upper
Unit (Upper) and the component parts of the unit
Neat Alignment Plate
When replacing the Finisher Controller PCB
Adjusting the Alignment
When replacing or installing/removing the Neat Stack
Position of the Lower
Unit (Lower) and the component parts of the unit
Neat Alignment Plate
When replacing the Finisher Controller PCB
Adjusting the Height of
When replacing the Finisher Controller PCB
Corrugation Roller for
Stack Delivery
Right Angle Adjustment
• When replacing the Front Alignment Motor
of Alignment Plate
• When replacing the Rear Alignment Motor
Adjusting Alignment
• When replacing the Front Alignment Motor
Plate Position
• When replacing the Rear Alignment Motor
• When replacing the Finisher Controller PCB
Adjusting Position of
When replacing the Stapler
Stapler
Adjusting Staple
When replacing the Finisher Controller PCB
Position (1-stapling at
the rear)
Adjusting Staple
Position (1-stapling at
the front)
Adjusting Staple
Position (2-stapling
positions)
Adjusting Delivery of
Staple Stack (lower
delivery)
Adjusting Delivery of
Staple Stack (saddle
delivery)
Saddle Stitch/Fold
Placement Adjustment
T-5-4
Symptom, adjustment timing
5-12
Reference
p. 5-14
p. 5-16
p. 5-17
p. 5-19
p. 5-21
p. 5-25
p. 5-26
p. 5-28
p. 5-29
p. 5-32
p. 5-35
p. 5-37
p. 5-40
p. 5-43
5-12
Advertisement
Table of Contents
