Table of Contents
Advertisement
DIPSW(SW382)
1
2
3
4
5
6
7
8
-
-
On -
On -
-
On M203
"Upper Neat Stack
M206
Unit Rear Alignment
Moter
Lower Neat Stack
Unit Rear Alignment
Moter"
-
-
On -
On -
On On M204
"Upper Neat Stack
M207
Unit Alignment Plate
Lifting Motor
Lower Neat Stack
Unit Alignment Plate
Lifting Motor"
-
-
On -
On On -
-
M208
"Lower Neat Stack
M209
Unit Return Roller
Lifting Motor
Upper Neat Stack
Unit Return Roller
Lifting Motor"
-
-
On -
On On On -
SL1
"Buffer path switch
SL2
solenoid
SL10
Upper path switch
SL11
solenoid
Assist Roller
Disengagement
Solenoid 1
Assist Roller
Disengagement
Solenoid 2
"
-
-
On On -
-
-
-
M106 Saddle folder/feeder
motor
6
Troubleshooting > Drive/Sensor check > Motor,Solenoid
Name
details
After pressing ENTER to start the
motor, use + to select upper or lower
(0: Upper Neat/1: Lower Neat).
Every press of ENTER changes
the operation as follows; Alignment
Plate phase alignment => Alignment
Plate positioning => Alignment Plate
initialization Then, use +/- to move 21
mm. Press ENTER again to terminate
the motor.
After pressing ENTER to start the
motor, use + to select upper or lower
(0: Upper Neat/1: Lower Neat).
Every press of ENTER changes the
operation as follows; Alignment Plate
phase alignment => Alignment Plate
positioning Then, use + to move to the
alignment position or - to move to the
shift position. Press ENTER again to
terminate the motor.
After pressing ENTER to start the
motor, use + to move to the return
position or - to move to the standby
position. Press ENTER again to
terminate the motor.
"After pressing ENTER, the solenoid
turns ON/OFF in the following order,
and then automatically terminates.
(1) Upper Path/Lower Path Switch
Flapper (2) Buffer Path Flapper (3)
Assist Roller Solenoid"
After pressing ENTER to start the
motor, use + to accelerate clockwise
in units of 30 mm/s in the range of 175
to 295 mm/s, or - to switch the rotation
direction. Press ENTER to terminate
the motor.
6
Troubleshooting > Drive/Sensor check > Motor,Solenoid
DIPSW(SW382)
1
2
3
4
5
6
7
8
-
-
On On -
-
-
On M105 Saddle paper push-
on plate motor
-
-
On On -
-
On -
M109 Stitcher motor
-
-
On On -
-
On On M101 Saddle transport
motor
-
-
On On -
On -
-
M104 Saddle guide motor Press ENTER to enter the mode, and
-
-
On On -
On -
On M103 Saddle lead edge
stopper motor
-
-
On On -
On On -
M102 Saddle alignment
guide motor
-
-
On On -
On On On M114
Saddle lead-in roller
disengage motor
-
-
On On On -
-
-
M107 Saddle delivery belt
motor
-
-
On On On -
-
On M109 Saddle sticher motor Press ENTER to start clinch operation,
-
-
On On On -
On -
M113
Saddle tapping
motor
Name
details
After pressing ENTER to start the
motor, use + to conduct push-on
operation. Press ENTER again to
terminate the motor. (NOTE: Push-
on is not performed unless the Roller
Guide is in HP.)
After pressing ENTER to start the
motor, use + to move to the standby
position of A3 (250 mm/s) or - to
perform press operation (100 mm/s).
Press ENTER again to terminate the
motor.
After pressing ENTER to start the
motor (665 mm/s), use +/- to switch
the speed (between 665 mm/s and
250 mm/s). Press ENTER again to
terminate the motor.
use + (Open)/-(Close). Press ENTER
again to terminate the mode (Open).
After pressing ENTER to start the
motor, use +/- to move in units of 20
mm in the range of 0 to 200 mm. Press
ENTER again to terminate the motor
(Home).
After pressing ENTER to start the
motor, use +/- to move in units of 10
mm in the range of 0 to 100 mm. Press
ENTER again to terminate the motor
(Home).
After pressing ENTER to start the
motor, use + to engage (in 2 stages,
switched alternately) or - to disengage.
Press ENTER again to terminate the
motor (Home).
After pressing ENTER to start the
motor, use + to rotate clockwise or - to
rotate counterclockwise. Press ENTER
again to stop the rotation and terminate
the motor.
which then terminates automatically.
After pressing ENTER to start the
motor, use + to tap or - to escape.
Press ENTER again to terminate the
motor.
6-5
6-5
Advertisement
Table of Contents
