Canon Finisher-AK1 Service Manual page 5

List of consumable parts locations -------------------------------------------- 4-7
Sensors ------------------------------------------------------------------------------- 4-8
Motors -------------------------------------------------------------------------------4-10
Solenoids ---------------------------------------------------------------------------4-12
PCBs ---------------------------------------------------------------------------------4-14
Switchs ------------------------------------------------------------------------------4-16
Fans ----------------------------------------------------------------------------------4-17
Removing from the connection equipment --------------------------- 4-18
Removing from the Host Machine --------------------------------------------4-18
External/Internal Covers --------------------------------------------------- 4-20
Removing the Rear Cover ------------------------------------------------------4-20
Removing the Rear Upper Cover (Right) -----------------------------------4-21
Removing the Rear Upper Cover (Left) -------------------------------------4-21
Removing the Inner Cover (Upper) -------------------------------------------4-22
Removing the Inner Cover (Lower) -------------------------------------------4-23
Electric Control Assembly ------------------------------------------------- 4-24
Removing the Finisher Controller PCB --------------------------------------4-24
Removing the Neat Stack Driver PCB ---------------------------------------4-24
Removing the Feed Motor Driver PCB --------------------------------------4-25
Removing the Saddle Stitcher Controller PCB ----------------------------4-25
Stacking Assembly ---------------------------------------------------------- 4-27
Points to Note on handling the Stack Wall Rail ---------------------------4-27
Removing the Stack Wall (Upper) --------------------------------------------4-27
Removing the Stack Wall (Lower) --------------------------------------------4-29
Points to Note on Tray A/B Cable ---------------------------------------------4-31
Position of Tray B at power-on ------------------------------------------------4-31
Removing the Tray A Unit -------------------------------------------------------4-32
Removing the Tray B Unit ------------------------------------------------------4-35
Adjusting Position of Tray A, B ------------------------------------------------4-37
Removing the Tray A/B Lifting Motor -----------------------------------------4-37
Feed Assembly -------------------------------------------------------------- 4-39
Removing the Delivery Static Eliminator ------------------------------------4-39
Removing the Upper Feed Unit -----------------------------------------------4-40
Removing the Inlet Feed Motor -----------------------------------------------4-42
Removing the Paper Trailing Edge Drop Motor ---------------------------4-43
Removing the Buffer Front Feed Motor -------------------------------------4-43
Removing the Buffer Motor -----------------------------------------------------4-44
Removing the Puncher Unit ----------------------------------------------------4-46
Removing the Side Registration Sensor Unit ------------------------------4-47
Removing the Side Registration Sensor PCB -----------------------------4-48
Removing the Side Registration Shift Unit ---------------------------------4-49
Removing the Side Registration Shift Motor -------------------------------4-53
Removing the Shift Motor -------------------------------------------------------4-54
Intermediate Process Tray Assembly ---------------------------------- 4-55
Removing the Stack Delivery Roller Upper Static Eliminator ----------4-55
Removing the Neat Paddle (Upper) ------------------------------------------4-55
Removing the Neat Paddle (Lower) ------------------------------------------4-56
Removing the Neat Stack Unit (Upper) -------------------------------------4-57
Removing the Neat Stack Unit (Lower) -------------------------------------4-59
Removing the Stapler ------------------------------------------------------------4-60
Adjusting Position of Stapler ---------------------------------------------------4-61
Removing the Process Tray Unit ----------------------------------------------4-62
Removing the Paddle Unit ------------------------------------------------------4-65
Removing the paddle ------------------------------------------------------------4-65
Removing the Stack Delivery Upper Roller --------------------------------4-66
Removing the Process Tray (Front) ------------------------------------------4-68
Removing the Process Tray (Rear) ------------------------------------------4-69
Removing the Feed Belt --------------------------------------------------------4-70
Removing the Stack Delivery Motor ------------------------------------------4-72
Removing the Process Tray Plate Unit --------------------------------------4-72
Removing the Front Alignment Motor ----------------------------------------4-73
Removing the Rear Alignment Motor ----------------------------------------4-75
Right Angle Adjustment of Alignment Plate---------------------------------4-77
Removing the Process Upper Guide Unit ----------------------------------4-78
Removing the Belt Controller Unit --------------------------------------------4-81
Removing the Belt Roller -------------------------------------------------------4-85
Saddle Stitcher Assembly ------------------------------------------------- 4-89
Removing the Saddle Inner Cover (Upper) --------------------------------4-89
Removing the Saddle Inner Cover (Lower) --------------------------------4-89
Removing the Saddle Inlet Roller Static Eliminator ----------------------4-90
Removing the Saddle Intermediate Static Eliminator --------------------4-91
Removing the Saddle Stapler --------------------------------------------------4-91