Mitsubishi Electric NZ2GF2B1-16D User Manual page 92

(4) NZ2EX2S1-16TE extension transistor output module (spring clamp terminal
block, source type)
Item
Number of output points
Rated load voltage
Max. load current
Isolation method
Max. inrush current
Leakage current at OFF
Max. voltage drop at ON
OFF  ON
*1
Output response time
ON  OFF
Surge suppressor
Voltage
External power supply for
output part
Current
Output type
Withstand voltage
Insulation resistance
Noise immunity
Protection degree
Wiring method for common
Overload protection
function
Protection function
Overheat protection
function
External interface I/O part
Applicable DIN rail
Applicable wire size For I/O
Terminal block for
Applicable solderless
terminal
output
RX/RY points
Cyclic transmission
RWr/RWw points
Module power supply Voltage
(supplied from the main
Current
module)
Weight
90
16 points
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
0.5A/point, 4A/common
Photocoupler isolation
Current is limited by the overload protection function.
0.1mA or less
0.3VDC (TYP.) 0.5A, 0.6VDC (MAX.) 0.5A
0.5ms or less
1.5ms or less (resistance load)
Zener diode
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
21mA or less (TYP. 24VDC per common) External load current is not included.
Source type
500VAC for 1 minute between all DC external terminals and the ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator
condition)
IP2X
16 points/common (1-wire, spring clamp terminal block type)
Limited current when overcurrent is detected (overload protection): 1A or more/point
Activated in increments of 1 point.
Activated in increments of 1 point.
Two-piece spring clamp terminal block
TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Stranded wire: 0.3 to 1.5 (22 to 16 AWG), terminal slot size: 2.2mm  1.65mm
TE 0.5-8, TE 0.5-10
TE 0.75-8, TE 0.75-10
TE 1.0-8, TE 1.0-10
TE 1.5-8, TE 1.5-10
AI 0.34-8TQ
*3
AI 0.5-8WH, AI 0.5-10WH
AI 0.75-8GY, AI 0.75-10GY
AI 1-8RD, AI 1-10RD
AI 1.5-8BK, AI 1.5-10BK
FA-VTC125T9
FA-VTCW125T9
16 points
0 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
30mA or less (24VDC, all points ON)
0.19kg
NZ2EX2S1-16TE
Applicable wire Bar solderless
size terminal tool
0.3 to 0.5
0.75
NH-79
0.9 to 1.0
1.25 to 1.5
0.3
0.5
0.75 CRIMPFOX6
1.0
1.5
0.3 to 1.65
FA-NH65A
0.3 to 1.6
*4
*2
Manufacturer
NICHIFU Co., ltd.
Phoenix Contact Co.,
Ltd.
Your local Mitsubishi
Electric sales office
or representative