Mitsubishi Electric NZ2GF2B1-16D User Manual page 53

(7) NZ2GFCM1-16DE main DC input module (MIL connector, negative common
type)
Item
Station type
Number of input points
Rated input voltage
Rated input current
Isolation method
Max. number of simultaneous input points
ON voltage/ON current
OFF voltage/OFF current
Input resistance
OFF  ON
*1
Input response time
ON  OFF
Input type
Withstand voltage
Insulation resistance
*3
Noise immunity
Protection degree
Wiring method for common
Communication part
Module power supply
External interface part
I/O part
Applicable DIN rail
Applicable wire size For power supply
RX/RY points
Cyclic transmission
RWr/RWw points
Communication cable
Availability of connecting extension module
Voltage
Module power supply
Current
Weight
*1 For how to calculate the processing time of the remote device station (input), refer to the point in the following.
Page 35, Section 4.2.1 (1)
If the input response time is set to "0ms", the actual input response time is 120s at OFF  ON, and 140s at ON 
*2
OFF.
*3 It is the noise immunity of when the input response time setting value is other than "0ms". Note that the module is easily
affected by noise if "0ms" is set.
*4 For how to calculate the current consumption when an extension module is connected, refer to "Calculating Current
Consumption". ( Page 92, Section 4.4)
Remote device station
16 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
4.0mA TYP. (for 24VDC)
Photocoupler isolation
Refer to the derating chart.
17VDC or more/3mA
8VDC or less/1.7mA or less
5.7k
*2
0ms /0.2ms/1ms/1.5ms/5ms/10ms/20ms/70ms
(Initial setting: 10ms)
Negative common (source type)
500VAC for 1 minute between all DC external terminals and the ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator condition)
IP2X
16 points/common (1-wire, MIL connector)
RJ45 connector
One-touch connector for power supply and FG (5 pins, crimping type)
Connector plug (sold separately): A6CON-PW5P, A6CON-PW5P-SOD
<Option> Online connector for power supply: A6CON-PWJ5P
MIL connector (20 pins)
The connector plug is sold separately.
TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
0.66 to 0.98 (18 AWG)
[Finishing outer diameter: 2.2 to 3.0mm (A6CON-PW5P), 2.0 to 2.3mm (A6CON-PW5P-SOD)]
Strand diameter: 0.16mm or larger
Insulating coating material: PVC (heat resistant vinyl)
16 points  (1 + number of extension modules)
8 points
An Ethernet cable that meets the 1000BASE-T standard:
Category 5e or higher (double shielded, STP), straight cable
Connectable (Max. one module)
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
180mA or less (24VDC, all points ON)
0.24kg
CHAPTER 4 SPECIFICATIONS
NZ2GFCM1-16DE
*4
4
51