Mitsubishi Electric NZ2GF2B1-16D User Manual page 61

(3) NZ2GF2B1(N)-16TE main transistor output module (screw terminal block,
source type)
Item
Station type
Number of output points
Rated load voltage
Max. load current
Isolation method
Max. inrush current
Leakage current at OFF
Max. voltage drop at ON
OFF  ON
Output response
*1
time
ON  OFF
Surge suppressor
Voltage
External power supply
for output part
Current
Output type
Withstand voltage
Insulation resistance
Noise immunity
Protection degree
Wiring method for common
Overload protection
function
Protection function
Overheat protection
function
Communication part
Module power supply
External interface part
I/O part
Applicable DIN rail
For power supply
Applicable wire size
For I/O
Terminal block for
module power supply
*2
and FG
Applicable solderless
terminal
Terminal block for
output
RX/RY points
Cyclic transmission
RWr/RWw points
Communication cable
NZ2GF2B1-16TE, NZ2GF2B1N-16TE
Remote device station
16 points
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
0.5A/point, 4A/common
Photocoupler isolation
Current is limited by the overload protection function.
0.1mA or less
0.5VDC (TYP.) 0.5A, 0.8VDC (MAX.) 0.5A
0.5ms or less
1.5ms or less (resistance load)
Zener diode
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
21mA or less (TYP. 24VDC per common) External load current is not included.
Source type
500VAC for 1 minute between all DC external terminals and the ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator condition)
IP2X
16 points/common (1-wire, screw terminal block type)
Limited current when overcurrent is detected (overload protection): 1.5A or more/point
Activated in increments of 1 point.
Activated in increments of 1 point.
RJ45 connector
Terminal block for module power supply and FG
Tightening torque range for terminal screw (M2.5 screw): 0.5 to 0.6Nm
18-point two-piece terminal block (M3 screw)
Tightening torque range for terminal screw (M3 screw  5.2): 0.43 to 0.57Nm
TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
Core: 0.5 to 1.5 (20 to 16 AWG)
Core: 0.3 to 2.0 (22 to 14 AWG)
TE 0.5-10
TE 0.75-10
TE 1.0-10
TE 1.5-10
AI 0.5-10WH
AI 0.75-10GY
AI 1-10RD
AI 1.5-10BK
RAV1.25-3 (compliant with JIS C
2805)
V2-MS3
RAP2-3SL
TGV2-3N
16 points  (1 + number of extension modules)
20 points
An Ethernet cable that meets the 1000BASE-T standard:
Category 5e or higher (double shielded, STP), straight cable
CHAPTER 4 SPECIFICATIONS
Applicable wire size Manufacturer
0.5
0.75
NICHIFU Co., ltd.
0.9 to 1.0
1.25 to 1.5
0.5
0.75
Phoenix Contact Co., Ltd.
1.0
1.5
0.3 to 1.25 
1.25 to 2.0 JST Mfg. Co., Ltd.
1.25 to 2.0 Nippon Tanshi Co., Ltd.
1.25 to 2.0 NICHIFU Co., ltd.
4
59