(5) NZ2GFCE3-16DE main DC input module (sensor connector (e-CON), negative
common type)
Item
Station type
Number of input points
Rated input voltage
Rated input current
Isolation method
Max. number of simultaneous input points
ON voltage/ON current
OFF voltage/OFF current
Input resistance
OFF ON
*1
Input response time
ON OFF
Input type
Withstand voltage
Insulation resistance
*3
Noise immunity
Protection degree
Wiring method for common
Communication part
Module power supply
part
External interface
I/O part
Applicable DIN rail
For power supply
Applicable wire size
For I/O
RX/RY points
Cyclic transmission
RWr/RWw points
Communication cable
Availability of connecting extension module
Voltage
Module power supply
Current
Weight
*1
For how to calculate the processing time of the remote device station (input), refer to the point in the following.
Page 35, Section 4.2.1 (1)
If the input response time is set to "0ms", the actual input response time is 120s at OFF ON, and 140s at ON
*2
OFF.
*3
It is the noise immunity of when the input response time setting value is other than "0ms". Note that the module is easily
affected by noise if "0ms" is set.
*4
For details, refer to "Recommended Connector List". ( Page 19, Section 1.5)
*5
For how to calculate the current consumption when an extension module is connected, refer to "Calculating Current
Consumption". ( Page 92, Section 4.4)
Remote device station
16 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
4.0mA TYP. (for 24VDC)
Photocoupler isolation
Refer to the derating chart.
17VDC or more/3mA
8VDC or less/1.7mA or less
5.7k
*2
0ms
/0.2ms/1ms/1.5ms/5ms/10ms/20ms/70ms
(Initial setting: 10ms)
Negative common (source type)
500VAC for 1 minute between all DC external terminals and the ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator condition)
IP2X
16 points/common (3-wire, sensor connector (e-CON))
RJ45 connector
One-touch connector for power supply and FG (5 pins, crimping type)
Connector plug (sold separately): A6CON-PW5P, A6CON-PW5P-SOD
<Option> Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) (4 pins, crimping type)
The connector plug is sold separately.
TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
0.66 to 0.98 (18 AWG)
[Finishing outer diameter: 2.2 to 3.0mm (A6CON-PW5P), 2.0 to 2.3mm (A6CON-PW5P-SOD)]
Strand diameter: 0.16mm or larger
Insulating coating material: PVC (heat resistant vinyl)
0.08 to 0.5 (28 to 20 AWG) (depends on the connector plug used (sold separately).)
16 points (1 + number of extension modules)
8 points
An Ethernet cable that meets the 1000BASE-T standard:
Category 5e or higher (double shielded, STP), straight cable
Connectable (Max. one module)
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
180mA or less (24VDC, all points ON)
0.27kg
CHAPTER 4 SPECIFICATIONS
NZ2GFCE3-16DE
*4
*5
4
*4
45