Mitsubishi Electric NZ2GF2B1-16D User Manual page 41

(3) NZ2GFCE3-16D main DC input module (sensor connector (e-CON), positive
common type)
Item
Station type
Number of input points
Rated input voltage
Rated input current
Isolation method
Max. number of simultaneous input points
ON voltage/ON current
OFF voltage/OFF current
Input resistance
OFF  ON
*1
Input response time
ON  OFF
Input type
Withstand voltage
Insulation resistance
*3
Noise immunity
Protection degree
Wiring method for common
Communication part
Module power supply
part
External interface
I/O part
Applicable DIN rail
For power supply
Applicable wire size
For I/O
RX/RY points
Cyclic transmission
RWr/RWw points
Communication cable
Availability of connecting extension module
Voltage
Module power supply
Current
Weight
*1 For how to calculate the processing time of the remote device station (input), refer to the point in the following.
Page 35, Section 4.2.1 (1)
If the input response time is set to "0ms", the actual input response time is 120s at OFF  ON, and 140s at ON 
*2
OFF.
*3 It is the noise immunity of when the input response time setting value is other than "0ms". Note that the module is easily
affected by noise if "0ms" is set.
*4 For details, refer to "Recommended Connector List". ( Page 19, Section 1.5)
*5 For how to calculate the current consumption when an extension module is connected, refer to "Calculating Current
Consumption". ( Page 92, Section 4.4)
Remote device station
16 points
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
4.0mA TYP. (for 24VDC)
Photocoupler isolation
Refer to the derating chart.
17VDC or more/3mA
8VDC or less/1.7mA or less
5.7k
*2
0ms /0.2ms/1ms/1.5ms/5ms/10ms/20ms/70ms
(Initial setting: 10ms)
Positive common (sink type)
500VAC for 1 minute between all DC external terminals and the ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator condition)
IP2X
16 points/common (3-wire, sensor connector (e-CON))
RJ45 connector
One-touch connector for power supply and FG (5 pins, crimping type)
Connector plug (sold separately): A6CON-PW5P, A6CON-PW5P-SOD
<Option> Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) (4 pins, crimping type)
The connector plug is sold separately.
TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
0.66 to 0.98 (18 AWG)
[Finishing outer diameter: 2.2 to 3.0mm (A6CON-PW5P), 2.0 to 2.3mm (A6CON-PW5P-SOD)]
Strand diameter: 0.16mm or larger
Insulating coating material: PVC (heat resistant vinyl)
0.08 to 0.5 (28 to 20 AWG) (depends on the connector plug used (sold separately).)
16 points  (1 + number of extension modules)
8 points
An Ethernet cable that meets the 1000BASE-T standard:
Category 5e or higher (double shielded, STP), straight cable
Connectable (Max. one module)
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
180mA or less (24VDC, all points ON)
0.27kg
CHAPTER 4 SPECIFICATIONS
NZ2GFCE3-16D
*4
*5
4
*4
39