Mitsubishi Electric NZ2GF2B1-16D User Manual page 68

(6) NZ2GFCE3-32T main transistor output module (sensor connector (e-CON),
sink type)
Item
Station type
Number of output points
Rated load voltage
Max. load current
Isolation method
Max. inrush current
Leakage current at OFF
Max. voltage drop at ON
OFF  ON
Output response
*1
time ON  OFF
Surge suppressor
Voltage
External power supply
for output part
Current
Output type
Withstand voltage
Insulation resistance
Noise immunity
Protection degree
Wiring method for common
Overload protection
function
Protection function
Overheat protection
function
Communication part
Module power supply
part
External interface
I/O part
Applicable DIN rail
For power supply
Applicable wire size
For I/O
RX/RY points
Cyclic transmission
RWr/RWw points
Communication cable
Availability of connecting extension module
Voltage
Module power supply
Current
Weight
66
Remote device station
32 points
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
0.5A/point, 6A/common
Photocoupler isolation
Current is limited by the overload protection function.
0.1mA or less
0.3VDC (TYP.) 0.5A, 0.6VDC (MAX.) 0.5A
0.5ms or less
1.5ms or less (resistance load)
Zener diode
12/24VDC (ripple rate: 5% or less) (Allowable voltage range: 10.2 to 28.8VDC)
8mA or less (TYP. 24VDC per common) External load current is not included.
Sink type
500VAC for 1 minute between all DC external terminals and the ground
10M or higher between all DC external terminals and ground (500VDC insulation resistance tester)
Noise voltage 500Vp-p, noise width 1s, noise frequency 25 to 60Hz (DC type noise simulator condition)
IP2X
32 points/common (3-wire, sensor connector (e-CON))
Limited current when overcurrent is detected (overload protection): 1A or more/point
Activated in increments of 1 point.
Activated in increments of 1 point.
RJ45 connector
One-touch connector for power supply and FG (5 pins, crimping type)
Connector plug (sold separately): A6CON-PW5P, A6CON-PW5P-SOD
<Option> Online connector for power supply: A6CON-PWJ5P
Sensor connector (e-CON) (4 pins, crimping type)
The connector plug is sold separately.
TH35-7.5Fe, TH35-7.5Al (compliant with IEC 60715)
0.66 to 0.98 (18 AWG)
[Finishing outer diameter: 2.2 to 3.0mm (A6CON-PW5P), 2.0 to 2.3mm (A6CON-PW5P-SOD)]
Strand diameter: 0.16mm or larger
Insulating coating material: PVC (heat resistant vinyl)
0.08 to 0.5 (28 to 20 AWG)
(depends on the connector plug used (sold separately).)
32 points +16 points  Number of extension modules
20 points
An Ethernet cable that meets the 1000BASE-T standard:
Category 5e or higher (double shielded, STP), straight cable
Connectable (Max. one module)
24VDC (ripple rate: 5% or less) (Allowable voltage range: 20.4 to 28.8VDC)
190mA or less (24VDC, all points ON)
0.35kg
NZ2GFCE3-32T
*2
*2
*3