Mitsubishi Electric NZ2GF2B-60TCTT4 User Manual page 77

Address
(decimal Target
Standard
(hexa- channel
control
decimal))
Simultaneous
temperature
732 (2DCH) CH4
rise group
setting
Simultaneous
temperature
733 (2DDH) CH4
rise gradient
data
Simultaneous
734 (2DEH) CH4 temperature
rise dead time
Simultaneous
temperature
735 (2DFH) CH4
rise AT mode
selection
736 to

1279(2E0H System area
to 4FFH)
*1 The default value depends on the mode used. For details on the default value, refer to the following.
Page 309, Appendix 3
*2 This column indicates whether data can be read from or written to the remote buffer memory area through sequence
programs.
R: Reading enabled
W: Writing enabled
*3 This column indicates whether the setting in the remote buffer memory area is automatically changed when the input
range is changed. For details, refer to the following.
Page 135, Section 8.1.6
*4 This column indicates whether data can be written to the non-volatile memory by turning off and on Set value backup
instruction (RY15). For details, refer to the following.
Page 136, Section 8.1.7
*5 This column indicates whether or not the setting can be changed by turning off and on During operation setting change
instruction (RY10). For details, refer to the following.
Page 295, Appendix 1.2 (3)
*6 This column indicates whether or not the setting can be changed by turning off and on Initial data setting request flag
(RY9) when all channels stop. For details, refer to the following.
Page 295, Appendix 1.2 (1)
*7 (TT) represents NZ2GF2B-60TCTT4. (RT) represents NZ2GF2B-60TCRT4.
*8 By using the setting change rate limiter, whether to set temperature rise/temperature drop in a batch or individually can
be selected. In the batch setting, the target of setting change rate limiter is only this area. In the individual setting, this
area is the setting target for the temperature rise. For details, refer to the following.
Page 167, Section 8.3.10
*9 Available only under the mix control (expanded mode). With other models, this area is handled as a system area.
*10 Available only under the heating-cooling control (expanded mode). With other models, this area is handled as a system
area.
*11 Available only under the mix control (normal mode). With other models, this area is handled as a system area.
*12 Available only under the heating-cooling control (normal mode). With other models, this area is handled as a system
area.
*13 By using the setting change rate limiter, whether to set temperature rise/temperature drop in a batch or individually can
be selected. In the batch setting, this area is handled as a system area. In the individual setting, this area is the setting
target for the temperature drop. For details, refer to the following.
Page 167, Section 8.3.10
*14 Available only when the NZ2GF2B-60TCTT4 is used. With other models, this area is handled as a system area.
Setting contents
Heating-
cooling Mix control
control
Simultaneous
temperature
System area 0
rise group
setting
Simultaneous
temperature
System area 0
rise gradient
data
Simultaneous
System area temperature 0
rise dead time
Simultaneous
temperature
System area 0
rise AT mode
selection

System area System area
Non-
volatile
Auto-
Default Read/ memory
matic
write
*1 *2
value Write
*3
setting
avail-
ability
 
R/W
R/W  
 
R/W
R/W  
  
CHAPTER 3 SPECIFICATIONS
Change
Change
of
of setting
setting
when all
Reference
during
channels
opera-
*6
stop
*4 *5
tion
Page 357,
 
Appendix
3 (59)
Page 357,
  Appendix
3 (60)
Page 358,
 
Appendix
3 (61)
Page 359,
  Appendix
3 (62)
  
75
3