Mitsubishi Electric NZ2GF2B-60TCTT4 User Manual page 318

(c) Resolution
The resolution is applied to the stored values and the set values of particular remote buffer memory areas as
described in the following table.
Resolution
1 Value in 1 ( or digit) unit is stored.
0.1 Value in 0.1 () unit (tenfold value) is stored.
For applicable remote buffer memory areas, refer to the following.
Page 362, Appendix 3 (68)
(d) When Auto-setting at input range change (address: 1H. b0) is Enable (1)
When the input range is changed, the following remote buffer memory areas are set automatically according to
selected temperature sensor. Set the remote buffer memory areas again if necessary.
Remote buffer memory area name
CH Upper limit setting limiter
CH Lower limit setting limiter
CH Process alarm lower lower limit value
CH Process alarm lower upper limit value
CH Process alarm upper lower limit value
CH Process alarm upper upper limit value
At the same time, the following remote buffer memory areas related to the input range is initialized to the
default value (0) automatically. Set the remote buffer memory areas again if necessary.
Remote buffer memory area name
CH Set value (SV) setting
CH Loop disconnection detection dead band
CH Alert set value 1
CH Alert set value 2
CH Alert set value 3
CH Alert set value 4
CH Sensor two-point correction offset value (measured value)
CH Sensor two-point correction offset value (corrected value)
CH Sensor two-point correction gain value (measured value)
CH Sensor two-point correction gain value (corrected value)
CH AT bias setting
CH Simultaneous temperature rise gradient data
CH Simultaneous temperature rise dead time
The remote buffer memory areas listed above are automatically set when CH Input range (address: 100H,
130H, 160H, 190H) is changed and Initial data setting request flag (RY9) is turned on and off.
(e) When Auto-setting at input range change (address: 1H. b0) is Disable (0)
Sometimes the setting value of remote buffer memory (Page 316, (5) (d)) might be out of setting range.
(When the setting range changes according to the change of the input range, the set value before the change
can turn out of the range.) In this case, a write data error (error code: 0004H) occurs in the remote buffer
memory area where the value turns out of the setting range. Change the input range after setting each remote
buffer memory area with values within the setting range after the input range change.
316
Stored value
CH1
10AH
10BH
251H
252H
253H
254H
CH1
101H
117H
224H
225H
226H
227H
284H
285H
286H
287H
2A1H
2D1H
2D2H
Set a value in 1 ( or digit) unit.
Value in 0.1 () unit (tenfold value).
Remote buffer memory address
CH2 CH3
13AH 16AH 19AH
13BH 16BH 19BH
25AH 263H 26CH
25BH 264H 26DH
25CH 265H 26EH
25DH 266H 26FH
Remote buffer memory address
CH2 CH3
131H 161H 191H
147H 177H 1A7H
22CH 234H 23CH
22DH 235H 23DH
22EH 236H 23EH
22FH 237H 23FH
288H 28CH 290H
289H 28DH 291H
28AH 28EH 292H
28BH 28FH 293H
2A3H 2A5H 2A7H
2D5H 2D9H 2DDH
2D6H 2DAH 2DEH
Set value
Reference
CH4
Page 325, Appendix 3 (14)
Page 350, Appendix 3 (47)
Reference
CH4
Page 317, Appendix 3 (6)
Page 335, Appendix 3 (26)
Page 348, Appendix 3 (45)
Page 352, Appendix 3 (52)
Page 353, Appendix 3 (53)
Page 353, Appendix 3 (54)
Page 354, Appendix 3 (55)
Page 355, Appendix 3 (57)
Page 357, Appendix 3 (60)
Page 358, Appendix 3 (61)