Henny Penny Velocity Series Operation Manual page 43

T T a a b b l l e e 5 5 - - 2 2 P P r r o o d d u u c c t t R R a a c c k k i i n n g g R R e e c c o o m m m m e e n n d d a a t t i i o o n n s s
G G e e n n e e r r a a l l M M a a r r k k e e t t
• 8-Head: Loads all four
racks as shown above.
• 6-Head: Loads racks 1, 2,
and 3 only.
• 4-Head: Loads racks 2 and
3 only.
• 2-Head loads rack 2 only.
5 5 . . 5 5 P P r r e e s s s s u u r r e e F F r r y y i i n n g g
D D o o n n o o t t o o v v e e r r l l o o a a d d t t h h e e r r a a c c k k s s w w i i t t h h p p r r o o d d u u c c t t ( ( 2 2 4 4 l l b b s s . . ( ( 1 1 0 0 . . 9 9 k k g g ) )
m m a a x x i i m m u u m m ) ) , , o o r r p p l l a a c c e e p p r r o o d d u u c c t t w w i i t t h h e e x x t t r r e e m m e e m m o o i i s s t t u u r r e e
c c o o n n t t e e n n t t i i n n t t o o f f r r y y e e r r . . D D o o i i n n g g s s o o c c a a n n c c a a u u s s e e b b o o i i l l o o v v e e r r o o f f t t h h e e o o i i l l
a a n n d d m m a a y y c c a a u u s s e e p p e e r r s s o o n n a a l l i i n n j j u u r r y y . .
• Push the Info button to see setpoint and true temperature of
N N O O T T E E :
• The heat cycles (pulses) on and off approximately 10
Watch a short video explaning the Info button.
T T R R A A I I N N I I N N G G :
Follow the procedure below to complete a cook cycle.
Make sure the vat is filled to the lower limit cold oil line. The line is etched in the
1 1 ) )
back of the vat.
Turn the power switch to the ON position.
2 2 ) )
Wait, allow fryer to heat until the setpoint is reached.
3 3 ) )
Before loading product onto the racks, lower the racks into the oil to keep the
4 4 ) )
product from sticking to the racks.
Load product as necessary onto the rack(s).
5 5 ) )
Slide the racks of breaded product onto the carrier on the lid, starting with the
6 6 ) )
bottom tier, to prevent damaged product.
Select product button and allow temperature to reach setpoint. Once the
7 7 ) )
setpoint has been reached, the display reads DROP.
Lower the lid until the front temporary lid latch locks into place.
8 8 ) )
2 2 H H e e a a d d B B a a g g s s
• 4-Bags: Loads all four
racks as shown above.
• 3-Bags: Loads racks 1, 2,
and 3 only.
• 2-Bags: Loads racks 2 and
3 only.
• 1-Bag: Load rack 2 only.
oil.
degrees before the setpoint temperature, to help prevent
overshooting the setpoint temperature (proportional control).
33