Rx I1 And Rx I2 Ports; Ports Menu - Transceiver Operation Mode; L (Local) Trx I2 Port - Lightware UBEX-PRO20-HDMI-F100 User Manual

 
     
3. Front Panel LCD Menu Operations 3. Front Panel LCD Menu Operations
HDMI Output
The following information are displayed in the case of both output ports of the receiver:
▪ HDCP mode - Auto / Always / Force 2.2 Type1
▪ Output 5V mode - Always on / Auto / Always off
▪ Hotplug detect
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
Source Mux
The source multiplexer (Source MUX) makes available routing more different source signals to the HDMI
output ports. See more details about this function in the
▪ Stream (D1) / Stream (D2) - The signal source of the output port is the stream coming from the remote
device.
▪ Loopback (I1) / Loopback (I2)- The signal source of the output port is the stream of the local input port
of the receiver.
▪ Copy (O1) - The device is able to copy the signal of the HDMI out 1 port. This is the COPY function.
INFO:
The Copy function is available only on the HDMI out 2 (TX O2) port.
3.5.3. RX I1 and RX I2 Ports
The following information is displayed for both local input ports:
The HDCP setting and information about the HDMI inputs are displayed:
▪ HDCP enable - Enabled / Disabled
▪ +5V present
▪ Signal present
Active resolution
▪
▪ Total resolution
▪ Color space
Receiver Mode section. #mux #sourcemux
#hdcp
Applied F-series endpoint firmware package: v2.0.0 | Applied R-series endpoint firmware package: v2.0.0 | LDC software: v2.5.9b3
series – Extender Application Mode – User's Manual series – Extender Application Mode – User's Manual
3.6. Ports Menu - Transceiver Operation Mode
#hdcp #power5v
The most important settings and status information of the HDMI input 1 and the
HDMI output ports are available in the Ports menu.
The three local HDMI ports and the remote HDMI ports of the connected device
are listed in the Ports menu of the transceiver.
INFO:

connected remote device. It is different when the connected device is another
transceiver, or a transmitter or a receiver.
Local ports
L TRX I2
L TRX O1
L TRX O2
Select the desired input or output port and enter to see the submenus.
3.6.1. L (Local) TRX I2 Port
HDMI Input
The HDCP setting and information about the HDMI input 1 port are displayed:
▪ HDCP enable - Enabled / Disabled
+5V present
▪
▪ Signal present
▪ Active resolution
Total resolution
▪
▪ Color space
Video Settings
The following settings can be set for the stream of the HDMI input 2 port:
▪
Resolution mode
– Passthrough: pass-through mode; the original resolution of the stream is transmitted.
– Forced: the resolution which is set in the Resolution setting menu is forced.
▪ Resolution setting - select a resolution to force from the pre-installed list. The entire list can be found in
the
▪ Image Position - Center
▪ Color space - Passthrough / Force RGB / Force YCbCr 4:4:4 / Force YCbCr 4:2:2
The displayed remote ports depend on the operation mode of the
Remote ports if the Remote ports if the
connected device is connected device is
TRANSCEIVER (TRX) TRANSMITTER (TX)
R TRX I2 TX I1
R TRX O1 TX I2
#hdcp
#frc
Resolutions of the Scaler / FRC section.
26 26
Remote ports if the
connected device is
RECEIVER (RX)
RX O1
RX O2
#csc #colorspace