ADTRAN ATLAS 810 Plus User Manual
  1. Manuals
  2. Brands
  3. ADTRAN Manuals
  4. Network Hardware
  5. ATLAS 810 Plus
  6. User manual
ADTRAN ATLAS 810 Plus User Manual

ADTRAN ATLAS 810 Plus User Manual

Adtran network device user manual
Hide thumbs Also See for ATLAS 810 Plus:
  • Q&a (22 pages)
Table of Contents

Advertisement

Quick Links

Download this manual
61200266L1-1A
July 1999
$7/$6ýåìí
8VHUý0DQXDO
3DUWý1XPEHUýìëííëçè/ì
3DUWý1XPEHUýìëííëçç/ì
3/86

Advertisement

Table of Contents
loading

Related Manuals for ADTRAN ATLAS 810 Plus

Summary of Contents for ADTRAN ATLAS 810 Plus

  • Page 1 $7/$6ýåìí 61200266L1-1A July 1999 3/86 8VHUý0DQXDO 3DUWý1XPEHUýìëííëçè/ì 3DUWý1XPEHUýìëííëçç/ì...
  • Page 2 DMS 100 is a registered trademark of Northern Telecom. 5ESS is a registered trademark of AT&T. AT&T is a registered trademark. 901 Explorer Boulevard P.O. Box 140000 Huntsville, AL 35814-4000 (256) 963-8000 © 1999 ADTRAN, Inc. All Rights Reserved. Printed in U.S.A.
  • Page 3 ADTRAN Year 2000 (Y2K) Readiness Disclosure ADTRAN has established a Year 2000 program to ensure that our products will correctly function in the new millennium. ADTRAN warrants that all products meet Year 2000 specifications regardless of model or revision. Information about ADTRAN's Year 2000 compliance program is available at the fol-...
  • Page 4 If they do, you will be given advance notice to give you an opportunity to maintain uninterrupted service. If you experience trouble with this equipment (ATLAS), please contact ADTRAN at (256) 963-8000 for repair/ warranty information. The telephone company may ask you to disconnect this equip- ment from the network until the problem has been corrected or until you are sure the equipment is not malfunctioning.
  • Page 5 Affidavit Requirements for Connection to Digital Services • An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and billing protection is used to transmit digital signals contain- ing encoded analog content which are intended for eventual conversion into voiceband analog sig- nals and transmitted on the network.
  • Page 6 rials and instructions provided by the manufacturer/grantee of the equipment used to encode analog signals; or ( ) C. An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the equipment used to encode analog signals; or ( ) D.
  • Page 7 The Industry Canada Certification label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facil- ities of the local telecommunications company.

  • Page 8: Chapter 7 Modules Terminal Menu

    • Chapter 11, SNMP Management, describes how to control the ATLAS 810 • Chapter 12, ADTRAN Utilities, describes the SysLog, Telnet, VT-100, and TFTP Server programs de- livered with the ATLAS 810 Appendices • Appendix A, System Event Logging, describes the events monitored by the ATLAS 810 •...
  • Page 9 Notes, cautions, and warnings provide other significant information. They are easily identified, as shown below: Notes provide additional useful information. Cautions signify information that could prevent service interruptions. Warnings provide information that could prevent damage to the equipment or endangerment to human life.

  • Page 11: Table Of Contents

    Base Unit ... 1-1 PLUS ATLAS 810 Features ... 1-6 Chapter 2 Installation... 2-1 Inspect the ADTRAN Shipment ... 2-1 Contents of ADTRAN Shipments ... 2-1 Check the Power Connection ... 2-1 AC Powered Unit... 2-2 DC Powered Unit... 2-2 Grounding Instructions...
  • Page 12 Table of Contents Chapter 4 Using the Front Panel ... 4-1 Overview ... 4-1 System LED ... 4-1 ACO Switch... 4-1 CRAFT Port ... 4-2 The Front Panel LEDs... 4-2 Chapter 5 Navigating the Terminal Menu ... 5-1 Terminal Menu Window... 5-1 Menu Path ...
  • Page 13 Ethernet Port ... 6-8 Chain Port ... 6-9 SNMP ... 6-9 Event Logging ... 6-12 Syslog Setup ... 6-12 Real Time Clock ... 6-12 Access Passwords ... 6-13 Licenses ... 6-14 BONDING Config ... 6-15 Alarm Relay Reset ... 6-15 Alarm Relay Threshold ...
  • Page 14 Table of Contents Port/PEP ... 9-3 Sig ... 9-3 Out#Accept ... 9-3 Out#Rej ... 9-5 Ifce Config ... 9-5 User Term ... 9-5 Slot/Svc, Port/PEP ... 9-5 Sig ... 9-6 In#Accept ... 9-6 Out#Rej ... 9-7 Ifce Config ... 9-8 Global Param ...
  • Page 15 Filtering (Disabling) Traps ... 11-3 Standard Traps... 11-3 DS1 Traps... 11-4 DS1 Alarm Traps ... 11-4 DS1 Alert Traps... 11-4 Chapter 12 ADTRAN Utilities ... 12-1 Overview... 12-1 SysLog Host Daemon ... 12-1 SysLog GUI... 12-2 Monitor ... 12-2 Menu Bar... 12-3 File ...
  • Page 16 Table of Contents Refresh Screen ... 12-9 Connect ... 12-9 Colors ... 12-9 Local Echo ... 12-9 AutoRepeat ... 12-9 Capture Menu... 12-9 Help Menu ... 12-9 Contents ... 12-9 About ... 12-9 TFTP Server... 12-10 Server Menu ... 12-11 Enable ...

  • Page 17: List Of Figures

    List of Figures Figure 1-1. Point-to-Point Circuit............1-2 Figure 1-2.
  • Page 18 List of Figures Figure 12-5. TFTP Server Interface Menu Tree ..........12-10 Figure 12-6.

  • Page 19: List Of Tables

    List of Tables Table 2-1. Control/Chain In Pinout ........... . . 2-5 Table 2-2.
  • Page 20 List of Tables PLUS ATLAS 810 User Manual 61200266L1-1...

  • Page 21: Product Overview

    Introduction Chapter 1 PRODUCT OVERVIEW The ATLAS 810 bust solutions for the wide area communication needs of medium-to-large corporations and network access providers. ATLAS is an Integrated Access System with the most extensive support of dedicated bandwidth manage- ment and access switching in the industry. The ATLAS 810 The ATLAS 810 munications drivers which allow the support of optional applications such...

  • Page 22: Figure 1-1. Point-To-Point Circuit

    Chapter 1. Introduction The ATLAS modules include the following: • HDLC Module • Quad T1/PRI Module • Octal Basic Rate ISDN Module • T3 Module • Async-232 Module • Modem-16 Module Frame Relay Frame relay is a packet-switched service that allows efficient transfer of bursty traffic in a WAN environment.

  • Page 23: Figure 1-2. Frame Relay Circuit

    The Frame Relay/Router upgrade option adds the capability for the ATLAS series of Integrated Access Devices to act as a voice/data FRAD, a frame re- lay switch, and an IP router in addition to the current available bandwidth manager and switch applications. Dedicated and Switched Connection Maps in a Single Platform The ATLAS 810 to five unique connection maps.

  • Page 24: Figure 1-3. Digital Access Cross-Connect System (Dacs)

    Additionally, T-Watch PRO, ADTRAN’s Microsoft management system, allows end-to-end management with downstream ADTRAN T1 products. User configurations can be preserved in non-volatile memory and duplicated for managing multiple ATLAS implementations. ATLAS also supports FLASH upgrades for future enhancements. You can remotely download software using TFTP or XMODEM.

  • Page 25: Figure 1-4. T1 Bandwidth Management

    ATLAS is ideal for point-to-point configurations or access to public networks. For optimization of existing equipment and network re- sources, ATLAS can be paired with ADTRAN’s TSU product offerings to support a variety of data and analog voice applications (see Figure 1-4).

  • Page 26: Atlas 810 Plus Features

    FEATURES Configuration and Management • VT-100 Emulation • T-Watch PRO, Microsoft Windows-based GUI • SNMP, per MIB II (RFC1213), DS1 MIB (RFC1406), and ADTRAN pri- vate MIBs • Telnet • Six levels of password protection and privileges Software Upgrade •...
  • Page 27 Dedicated Connection Maps • Up to five connection maps • Time of day/day of week configurable • Preserves signaling through cross-connect • No effect on nonconfigured channels Switched Connection Maps • Inbound and outbound call filtering and blocking Testing • Local and remote: payload/line, V.54 •...
  • Page 28 Chapter 1. Introduction PLUS ATLAS 810 User Manual 61200266L1-1...

  • Page 29: Inspect The Adtran Shipment

    Before installing the ATLAS 810 Base Unit for shipping damage. If you suspect damage, file a claim immedi- ately with the carrier and then contact ADTRAN Technical Support (see Warranty and Technical Support Information on page C-1). If possible, keep the original shipping container for returning the ATLAS 810 for verification of damage during shipment.

  • Page 30: Ac Powered Unit

    Chapter 2. Installation AC Powered Unit The AC powered ATLAS 810 detachable 8-foot power cord with a 3-prong plug for connecting to a grounded power receptacle. DC Powered Unit The DC powered ATLAS 810 terminal block on the rear of the unit. The power source should be connected to the terminal block according to the polarity markings on the unit.

  • Page 31: Review The Rear Panel Design

    A supplementary equipment grounding conductor shall be installed be- tween the product or system and ground that is in addition to the equipment grounding conductor in the power supply cord. The supplementary equipment grounding conductor shall not be smaller in size than the ungrounded branch-circuit supply conductors.

  • Page 32: Control/Chain In Port

    Chapter 2. Installation Control/Chain Out Connects to Chain In of another unit 10 Base T Control/ RJ-48C Connec- Chain In tion Port Interface of Chain In CAUTION: MAINTENANCE TO BE PERFORMED BY TRAINED SERVICE PERSONNEL ONLY CONTROL /CHAIN 10 BASE T ALL EMPTY SLOTS MUST BE COVERED WITH BLANK PANELS Blank panel covering an unused option slot...

  • Page 33: Control/Chain Out Port

    Connection The Control/Chain In connection follows with the pinout shown in Table 2-1. Connector type Part number Control/Chain Out Port The Control/Chain Out port (RJ-48C) connects to another ATLAS 810 Chain In connector. The Control/Chain Out port output provides the fol- lowing: •...

  • Page 34: Ethernet 10Baset Connection

    Chapter 2. Installation 6,7,8 Ethernet 10BaseT Connection The 10BaseT Ethernet port (RJ-48C) provides an Ethernet LAN connection, which is used for TFTP, SNMP, and Telnet connection. Connection The network connection follows, with the pinout shown in Table 2-3. Connector type (USOC) Part number Table 2-2.

  • Page 35: Alarm Relay Connection

    Alarm Relay Connection This connection alerts the user when a selected alarm condition exists. The four-pin, removable terminal block connects with external wiring. To make the appropriate connections, remove the block, connect wiring as needed, and return the terminal block to the connector socket. Clear the alarm con- dition by pressing the Alarm Cut-Off (ACO) switch located on the font panel of the ATLAS 810 Connection...

  • Page 36: Network Connection

    Chapter 2. Installation Network Connection The two eight-pin modular jacks labeled NTWK 1 and NTWK 2 provide the network connection. The two Network Interface (NI) ports comply with the applicable ANSI and AT&T tions: • AMI or B8ZS coding • Manual line build out •...

  • Page 37: Option Slots

    Option Slots Figure 2-3 shows the option slot numbering designation, as viewed from the rear of the ATLAS 810 and 8, which can also accommodate an optional power supply for redun- dancy. INSTALL ANY OPTION MODULES After installing the base ATLAS 810 quired cables, you can install your choice of option modules.
  • Page 38 Chapter 2. Installation PLUS 2-10 ATLAS 810 User Manual 61200266L1-1...

  • Page 39: Chapter 3 Operation

    VT-100 terminal-emulation software.) To receive the full benefit of the terminal menu interface, you should use a fully VT-100 com- patible client. The ADTRAN Utilities floppy disks (that you can install on a PC) contain both a VT-100 client and a customized Telnet program. See ADTRAN Utilities on page 12-1 for details on the available programs.
  • Page 40 Action Set the baud rate on the VT-100 terminal to 9600 baud (8/N/1). Use the ADTRAN-provided VT-100 terminal adapter to connect the COM port of a VT-100 compatible terminal, or equivalent, to the eight-pin modular jack labeled CONTROL/CHAIN IN on the rear panel or labeled CRAFT on the front panel.

  • Page 41: Using Telnet

    (see Session Timeout on page 6-8 for details). USING T-WATCH PRO T-Watch PRO is the ADTRAN Microsoft Windows management software program designed to control TSU units from a remote PC. It provides limit- ed control over the configuration of the ATLAS 810 terface.
  • Page 42 Chapter 3. Operation PLUS ATLAS 810 User Manual 61200266L1-1...

  • Page 43: Chapter 4 Using The Front Panel

    Using the Front Panel Chapter 4 OVERVIEW The front panel contains the System LED, the Alarm Cut-off (ACO) switch, and the CRAFT port. The front panel also contains controller and module status LEDs that provide visual information about the ATLAS 810 Unit and any option module that may be installed.

  • Page 44: Craft Port

    Chapter 4. Using the Front Panel CRAFT PORT Use the CRAFT port to configure the system via an EIA-232 connection. The CRAFT port provides the same functions and operations as the Control In port located on the rear panel of the ATLAS 810 CRAFT port pinout (see also CRAFT Port on page 4-3 in Table 4-2).
  • Page 45 Feature Controller Status LEDs Indicates the status of both network interfaces. (See also Table 4-3 on page 4-4.) Indicates that both integral network interfaces are operating correctly. Test Indicates that one of the network interfaces is in a test mode. Error Blinks to indicate the occurrence of error events.

  • Page 46: Table 4-3. Led Descriptions

    Chapter 4. Using the Front Panel For these LEDs... This color light... System Green (solid) Green (fast blink) Yellow (solid) Red (solid) Red (fast blink) Controller Status OK (green) Test (yellow) Error (flashing red) Indicates an error such as BPV (bipolar violation), Alarm (red) Module Status Green (solid)

  • Page 47: Chapter 5 Navigating The Terminal Menu

    Navigating the Terminal Menu Chapter 5 TERMINAL MENU WINDOW The ATLAS 810 menu items and data fields. All menu items and data fields display in the terminal menu window, through which you have complete control of the ATLAS 810 Menu Path Left Pane Tool Tip Menu Path...

  • Page 48: Window Panes

    Chapter 5. Navigating the Terminal Menu Window Panes When you first start a terminal menu session, the terminal menu window is divided into left and right panes. The left pane shows the list of available submenus, while the right pane shows the contents of the currently selected submenu.

  • Page 49: Additional Terminal Menu Window Features

    Additional Terminal Menu Window Features The following features are located across the bottom of the window: Tool Tip Port Status Extended Help Navigation Help System Time NAVIGATING USING THE KEYBOARD KEYS You can use various keystrokes to move through the terminal menu, to man- age a terminal menu session, and to configure the system.

  • Page 50: Session Management Keystrokes

    Chapter 5. Navigating the Terminal Menu To do this... Move between the left and right panes. Move to the top of a screen. Move to the bottom of a screen. Ascend one menu level. Session Management Keystrokes To do this... Log out of a session.

  • Page 51: Configuration Keystrokes

    Configuration Keystrokes To do this... Restore factory default settings. This setting restores the factory defaults based on the location of the cursor. If the cursor is on a module line (in the Modules menu), then only the selected module is updated to factory defaults. Copy selected items to the clipboard.
  • Page 52 Chapter 5. Navigating the Terminal Menu PLUS ATLAS 810 User Manual 61200266L1-1...

  • Page 53: Selecting The Appropriate Menu

    Terminal Menu and System Chapter 6 Control SELECTING THE APPROPRIATE MENU The terminal menu is the access point to all other operations. Each terminal menu item has several functions and submenus that identify and provide ac- cess to specific operations and parameters. Use the chart below to help you select the appropriate terminal menu.

  • Page 54: Security Levels

    Chapter 6. Terminal Menu and System Control Security Level To help you follow the terminal menu hierarchy, the following notations are used: MENUS > » Submenus »» Sub-submenus SYSTEM INFO > The System Info menu provides basic information about the unit as well as data fields for editing information.

  • Page 55: System Name

    » System Name Security level: 3; Read security: 5 Provides a user-configurable text string for the name of the ATLAS 810 This name can help you distinguish between different installations. You can enter up to 40 alpha-numeric characters in this field, including spaces and special characters (such as an underbar).

  • Page 56: Boot Rom Rev

    Chapter 6. Terminal Menu and System Control » Boot ROM Rev Read security: 5 Displays the boot ROM revision. SYSTEM > The System Status menu provides information on the status of the unit. STATUS Figure 6-2 shows the submenu functions available in the System Status menu.

  • Page 57: Clear System Event Log

    » Clear System Write security: 3; Read security: 5 Event Log Clears the event log. When you select the command, the following prompt displays: the log or » Ethernet Port Read security: 5 Displays status information about the Ethernet port. An asterisk (*) indi- cates activity for the item.

  • Page 58: Resource Usage

    Chapter 6. Terminal Menu and System Control » Resource Usage Write security: 4; Read security: 5 Indicates resource use (analog modems; digital modems; voice compres- sion). »» Data Tables Tracks resource usage for dynamic resources throughout the system and presents the information in a table format. Resource Type Displays the system resources list.

  • Page 59: Chain Port Overrun Errs

    » Chain Port Rx Read security: 5 Bytes Displays the number of received data bytes. » Chain Port Read security: 5 Displays the number of overrun errors. Overrun Errs » Chain Port Read security: 5 Displays the number of received framing errors. Framing Errs »...

  • Page 60: Adlp Address

    » ADLP Address Write security: 2; Read security: 5 Shows the system ADTRAN Data Link Layer Protocol (ADLP) address for connecting remote devices to management software (such as T-Watch PRO). The allowable range is between 2 and 65520. Enter a value not used by any of the TSU units controlled by the management software.

  • Page 61: Chain Port

    » Chain Port Write security: 2; Read security: 5 Accepts input for configuring the Chain In port. Write security: 2; Read security: 5 »» Port Name Defines the name of the chain port. Type in an alpha-numeric name up to 57 characters long.
  • Page 62 Chapter 6. Terminal Menu and System Control Write security: 3; Read security: 5 »» Trap Transmission Enables and disables SNMP trap transmission. »» Authen Trap Write security: 3; Read security: 5 Enables and disables the authentication failure trap. Transmission »» Traps Destination Write security: 3;...
  • Page 63 Current CSS Thrsh The DS1 performance monitor Threshold Value for the Current 15 minute Controlled Slip Seconds (SES) parameter. The default value is 1 for an ap- proximate BER level of 10E-5. Current PCV Thrsh The DS1 performance monitor Threshold Value for the Current 15 minute (D4) Path Code Violation (PCV) parameter, when the Line Type is Super Frame (AT&T D4 format) DS1.

  • Page 64: Event Logging

    Write security: 3; Read security: 5 Configures the ATLAS Syslog client for use with a Syslog server (supplied on ADTRAN /Utility disk or available on most UNIX platforms). »» Transmission Enables or disables the transmission of log events to the external Syslog server.

  • Page 65: Access Passwords

    Instructions for Adding/Deleting Passwords Select the first column select the first column PLUS If you lose or forget the ATLAS 810 password, contact ADTRAN technical support (see inside back cover) for help in resetting the password. Passwords are case-sensitive. PLUS ATLAS 810 User Manual õíô...

  • Page 66: Licenses

    Chapter 6. Terminal Menu and System Control Step »» Access Rights Write security: 0; Read security: 5 Defines the password level for the corresponding label. You can select from six different password levels (see also Table 6-1 on page 6-2). Write security: 0;...

  • Page 67: Bonding Config

    » BONDING Config »» TXINIT Timer (sec) This option specifies the length of time the originating endpoint attempts to detect the BONDING negotiation pattern from the answering endpoint be- fore deciding the BONDING call has failed. »» TXFA Timer (sec) This option specifies the length of time both endpoints attempt to detect the BONDING frame pattern when a call is connected before deciding the BONDING call has failed.

  • Page 68: System Utility

    Chapter 6. Terminal Menu and System Control SYSTEM > Use the System Utility menu to view and set the system parameters shown UTILITY in Figure 6-4. » Update Firmware Write security: 1; Read security: 5 Updates firmware when ATLAS 810 transfer methods are available for use in updating any modules that contain Flash memory—including the ATLAS system controller.
  • Page 69 »» Module Type Write security: 1; Read security: 5 Reflects the module type selected in Module Slot. This is normally a read- only field; however, if you selected All Modules of a Type, you must select a particular module type to update all modules of that type. The selections only include upgradable modules.

  • Page 70: Update Status

    Chapter 6. Terminal Menu and System Control Read security: 5 »» Current Update Indicates progress or problems encountered during the current update pro- Status cess. The field displays Idle if no update is in progress or when the update is successfully completed. At the end of a successful update, the contents of this field are copied into Previous Update Status.
  • Page 71 To support these transfers, ADTRAN delivers a TFTP program with ATLAS 810 crosoft Windows with this software, and store a configuration file. See TFTP Server on page 12-10 for details on how to use TFTP Server. Only one configuration transfer session (upload or download) can be active at a time.

  • Page 72: System Utilization

    » System Utilization Write security: 0; Read security: 0 Displays statistics related to the ATLAS internal operating system. Please check with ADTRAN Technical Support before attempting to use this menu. » System Selftest Write security: 3; Read security: 5 Initiates a system self-test.

  • Page 73: Figure 6-5. View Self-Test Log

    »» View Selftest Log Read security: 5 Displays time-stamped log of the tests conducted and the Pass/Fail results. Self-tests verify data integrity and processor control to each port. Each port is looped back and a data pattern is sent and tested. The result of the self-test on each installed port is listed with Pass/Fail re- sults.

  • Page 74: Ping

    Chapter 6. Terminal Menu and System Control Write security: 3; Read security: 5 »» Clear Self-test Log Clears the self-test log. » Ping Write security: 5; Read security: 5 Allows you to send pings (ICMP requests) to devices accessible via the net- work.

  • Page 75: Reboot System

    »» Start/Stop Write security: 5; Read security: 5 If the ping client is currently idle, this menu sends pings to the specified address. If the ping client is active, the menu stops sending pings. » Reboot System Write security: 2; Read security: 5 Reboots the ATLAS 810 message displays: reboot the system, or...
  • Page 76 Chapter 6. Terminal Menu and System Control PLUS 6-24 ATLAS 810 User Manual 61200266L1-1...

  • Page 77: Chapter 7 Modules Terminal Menu

    Modules Terminal Menu Chapter 7 To help you follow the terminal menu hierarchy, the following notations are used: MENUS > » Submenus »» Sub-submenus MODULES > Write security:3; Read security:5 The Modules menu provides options that allow you to configure and con- trol the installed option modules as well as the controller T1/PRI ports.

  • Page 78: Slt

    Chapter 7. Modules Terminal Menu » Slt Write security:3; Read security:5 Identifies the slot number. Slot 0 refers to the ATLAS 810 » Type Write security:3; Read security:5 Displays the type of module actually installed in the slot or the type of module you plan to install in the slot.

  • Page 79: State

    » State Read security:5 Displays whether the module is online of offline. Even though a module is physically installed, it must be marked available resource. This parameter allows an installed module to be marked Offline Offline » Status Read security:5 Displays status information on the ATLAS 810 installed modules as follows: Online...

  • Page 80: Modules Menu (Quad T1/Pri)

    Chapter 7. Modules Terminal Menu Modules Menu (Quad T1/PRI) This section provides detailed information on the Modules/Menu sub- menus. Menu provides access to commands that allow you to review the sta- tus of various options, change the configuration for general parameters, and initiate tests.
  • Page 81 »» DS0 Status Read security:5 Indicates usage on a DS0 basis for each port as follows. »» DS0 Alarms Indicates DS0 alarm as follows: Read security:5 »» Sig Status Indicates signaling of all 24 DS0s. The A/B bits for Rx and Tx DS0s are shown for each port.
  • Page 82 Chapter 7. Modules Terminal Menu Line Code Violations. Path Code Violations. Line Errored Seconds. »» Performance: 15 Min Write security:3; Read security:5 In the Performance 15 min. menu, the performance data for the previous 15 minute window is stored. Refer to Performance: Curr on page 7-5 for a detailed description.
  • Page 83 »» Test Initiates different types of tests and displays test results. Identifies the port number. Loc LB Read security:5 (Local Loopback) Causes loopback on near-end port. Line Payld Remote LB Write security:4; Read security:5 (Remote Loopback) Sends a loopback code to a remote CSU. ANSI FDL Line ANSI FDL Pyld AT1 Inband l...
  • Page 84 Chapter 7. Modules Terminal Menu PLUS ATLAS 810 User Manual 61200266L1-1...

  • Page 85: Overview

    Dedicated Maps Terminal Chapter 8 Menu OVERVIEW The Dedicated Maps menu assigns dedicated connections between any two ports in the ATLAS 810 Maps menu items (see Figure 8-1). In addition, step-by-step instructions are provided for setting up a sample dedicated map (see Creating A Dedicated Map on page 8-6).

  • Page 86: Chapter 8 Dedicated Maps Terminal Menu

    Chapter 8. Dedicated Maps Terminal Menu ACTIVATE > Write security:3; Read security:5 Activates a dedicated map—automatically or manually. You can have up to five different dedicated maps, each with an optionally specified name. » Auto Automatically activates a particular dedicated map at the time and day specified in Activate Time (see Activate Time on page 8-5).
  • Page 87 »» # (Index Number) Displays the number of the dedicated map connection. If you press nection, numbered consecutively. Write security:3; Read security:5 »» FROM Slt (From Slot) Specifies the slot to use for the FROM connection. When you select this option, a list of all of the slots and the modules installed in the slots displays.
  • Page 88 Chapter 8. Dedicated Maps Terminal Menu Trunk Conditioning Write security: 3; Read security: 5 Sets known values in the signaling bits and the data field for outgoing DS0s which are cross-connected to a T1 port experiencing alarms. The trunk conditioning process consists of a 2.5-second transmission (indicating call termination), followed by a continuous transmission signaling the final condition as chosen by the user.

  • Page 89: Activate Time

    »» TO Slot Write security: 3; Read security: 5 Specifies the slot to use for the second end of a connection. Select this option, and a list of all of the slots and the modules installed in the slots dis- plays.

  • Page 90: Designing The Dedicated Map For Example 2

    Chapter 8. Dedicated Maps Terminal Menu For this example, assume voice traffic is received on T1-A, and T1-B is groomed onto T1-C to the PBX (see Figure 8-2). If T1-A fails, the DS0s which were cross-connected to T1-C will receive trunk conditioning. Example 2 Creating A Dedicated Map A dedicated map defines connections for dedicated bandwidth between...

  • Page 91: Configuring The Ports For Example 2

    by-step procedures for creating a sample dedicated map based on the con- nections and ports given in Table 8-1. PLUS Name ATLAS 810 Port Controller T1 Data A Slot 0 Port 1 Controller T1 Data B Slot 0/Port 2 Quad T1/PRI Data C Slot 1/Port 1 Controller T1...

  • Page 92: Defining The Connections For Example 2

    Chapter 8. Dedicated Maps Terminal Menu Defining the Connections for Example 2 Begin by navigating to Dedicated Maps/Create/Edit Maps and naming your map. Navigate to Dedicated Maps/Connects. The Connects sub- menu defines the connections necessary to route the required bandwidth. Refer to Table 8-1 on page 8-7 to define each of the necessary connections.
  • Page 93 Step Step 61200266L1-1 Chapter 8. Dedicated Maps Terminal Menu Instructions for Defining Data Connections (Continued) Action Paste this information onto a new connection line by positioning the cursor over the index numbers of the new connections, and pressing Modify these connection lines to complete the connections for data.

  • Page 94: Figure 8-5. Completed Dedicated Map

    Chapter 8. Dedicated Maps Terminal Menu Figure 8-5. Completed Dedicated Map PLUS 8-10 ATLAS 810 User Manual 61200266L1-1...

  • Page 95: Chapter 9 Dial Plan Terminal Menu

    Dial Plan Terminal Menu Chapter 9 OVERVIEW The Dial Plan submenus (see Figure 9-1) set global ATLAS switch parame- ters as well as individual parameters for each ATLAS port handling a switched call. The individual ports are separated into two port types: net- work and user.

  • Page 96: Figure 9-2. Dial Plan Menu Tree

    Chapter 9. Dial Plan Terminal Menu Network Term Dial Plan User Term Global Param Slot/Svc Src ID Port/PEP Accept Number Search Out # Accept Data 64K Data 56K Audio Speech Treat Call As Reject Number Out#Rej Data 64K Data 56K Audio Speech Ifce Config...

  • Page 97: Network Term

    NETWORK This menu allows the user to define option parameters for ports which ter- > TERM minate a connection from the Network (PSTN). » Slot/Svc Write security: 3; Read security: 5 Selects the ATLAS slot that terminates a Network connection. »...
  • Page 98 Chapter 9. Dial Plan Terminal Menu Designates which numbers this endpoint passes on toward the Network »» Accept Number (PSTN). The accept list may consist of multiple entries. The numbers are defined using the following “wild cards”: [1,2,3...] = A single digit in this group For example, 1-800-$ only permits toll free long distance calls to 1-800.

  • Page 99: Out#Rej

    » Out#Rej Write security: 3; Read security: 5 Defines the parameters for the outgoing calls that ATLAS will not send to the Network. »» Reject Number Identifies which numbers this endpoint will not pass on toward the Net- work (PSTN). The reject list may consist of multiple entries. The reject list may be used to more easily specify the call filtering desired.

  • Page 100: Sig

    Chapter 9. Dial Plan Terminal Menu » Sig Write security: 3; Read security: 5 (User Selection - RBS; PRI) Defines the type of signaling being used for this connection (endpoint). Select RBS for a T1 using Robbed Bit Signaling, NFAS for a Primary Rate ISDN interface using Non-Facility Associated Sig- naling, and PRI for a Primary Rate ISDN interface.

  • Page 101: Out#Rej

    »» Search Write Security: 3; Read Security: 5 Defines to ATLAS the order in which to search for an accept number. Primary Search The Search parameter instructs ATLAS which order to search for an accept number match. Normally all searches are set to primary. The secondary search selection would be used to force ATLAS to only accept a call at this endpoint if all primary endpoints were unavailable.

  • Page 102: Ifce Config

    Chapter 9. Dial Plan Terminal Menu Rejects outgoing calls based on call type. For example, setting the reject »» Data 56K, Data 64K, number to $, Digital 56/64 to enabled, and Audio and Speech to disabled, Audio, Speech rejects all digital calls while not rejecting analog calls. »...

  • Page 103: Number Type Templates

    » Number Type Write security: 1; Read security: 5 Templates Sets call type patterns. ISDN interfaces require that a number type be sent over the D channel when a call is sent or received. A normal RBS trunk does not send a type designator, but uses prefixes instead. For example, “1 +” prefix is a national long distance call type while a “011 +”...

  • Page 104: Quad T1/Pri Module (Network Termination/Pri)

    Chapter 9. Dial Plan Terminal Menu INTERFACE CONFIGURATIONS This section describes Dial Plan Network Termination and User Termina- tion configuration settings for the following modules. Quad T1/PRI Module (Network Termination/PRI)....page 9-10 Quad T1/PRI Module (Network Termination/NFAS).
  • Page 105 »» Outgoing Number Write Security: 3 Read Security: 5 Conversion Defines the rules for converting as-dialed numbers into ISDN number type and plan. As dialed Send digits provided as unknown number type. ISDN - National pref Convert to ISDN type, using the 10-digit national form if possible. ISDN - Subscriber Convert to ISDN type, using the 7-digit subscriber form if possible.

  • Page 106: Quad T1/Pri Module (Network Termination/Nfas)

    Chapter 9. Dial Plan Terminal Menu Write Security: 3 Read Security: 5 »» Outgoing Caller ID Inserts a called ID based on the following selections: Send as provided ATLAS forwards whatever ID it receives (including None). ATLAS inserts a User-defined ID value if no value is received. Substitute if not present ID Presentation...

  • Page 107: Secondary Interfaces

    lowing configuration menu is available (in addition to the standard Net- work Termination/PRI configuration menus and options): » Secondary Write security: 3; Read security: 5 Interfaces Defines the additional PRI interfaces controlled by the D-channel on this endpoint. » Slot, Port Write security: 3;...
  • Page 108 Chapter 9. Dial Plan Terminal Menu Read security: 5 »» DS0s Available Indicates which DS0s of the T1 have been defined in this switched endpoint (indicated by “! “), in another switched endpoint (indicated by “s”), or in a dedicated map (indicated by “n”). The following symbols may display in this field: digits 0—9 »»...
  • Page 109 »» Trunk Number Write security: 3; Read security: 5 Defines to ATLAS the number to use to determine which user endpoint should receive the incoming call, when the Network connection does not provide DID digits. This field only displays when Direct Inward Dialing is set to Disabled.

  • Page 110: Quad T1/Pri Module (User Termination/Pri)

    Chapter 9. Dial Plan Terminal Menu Quad T1/PRI Module (User Termination/PRI) When you are working in the User Termination section of the Dial Plan menu, Slot is defined as a T1/PRI module, and Sig is set to PRI, the follow- ing configuration options are available: »»...

  • Page 111: Id Presentation

    »» Outgoing Caller ID Write Security: 3 Read Security: 5 Allows the user to insert a called ID to outgoing calls (coming in from attached User equipment). If set to ward whatever ID it receives (including none). If set to SUHVHQW If set to in place of the value received.

  • Page 112: Quad T1/Pri Module (User Termination/Rbs)

    Chapter 9. Dial Plan Terminal Menu » Interface Number Write security: 3; Read security: 5 Defines the interface number that uniquely identifies each additional inter- face. Quad T1/PRI Module (User Termination/RBS) When you are working in the User Termination section of the Dial Plan menu, Slot is defined as a T1/PRI module, and Sig is set to RBS, the follow- ing configuration options are available: Write security: 3;...

  • Page 113: Caller Id Number

    DID Prefix Write security: 3; Read security: 5 Defines to ATLAS the prefix digits which are not received as a part of the DID number. ATLAS uses the combination of prefix and DID number to determine the User endpoint that should receive the incoming call. »...

  • Page 114: Quad Nx56/64 Module (User Termination)

    Chapter 9. Dial Plan Terminal Menu Quad Nx56/64 Module (User Termination) When you are working in the User Termination section of the Dial Plan menu, and Slot is defined as a QuadNx56/64 module, the following inter- face configuration options are available: »»...

  • Page 115: Octal Bri Module (User Termination)

    Calls The number of calls (1 or 2) which can be received or sent on this number/ SPID. D64, D56, Audio, These options reflect what the Network has provisioned for this SPID. If the Speech BRI was purchased with different services provisioned for the SPIDs, then the call must match the services supported.

  • Page 116: Creating Dial Plans-Examples

    Chapter 9. Dial Plan Terminal Menu CREATING DIAL PLANS—EXAMPLES The ATLAS Dial Plan acts as the numbering plan for switched connections. This menu defines to ATLAS the phone numbers and features associated with dual-tone-multifrequency (DTMF) dialing, Primary Rate ISDN (PRI), and Basic Rate ISDN (BRI).

  • Page 117: Figure 9-4. Point-To-Point

    Example 2 Point-to-Point Connection Dial Plan Configuration In this example, ATLAS A operates as the network while ATLAS B termi- nates the network. That is, ATLAS A emulates the network and its PRI inter- face acts as the User termination. The PRI interface of ATLAS B acts as the Network termination (see Figure 9-4).
  • Page 118 Chapter 9. Dial Plan Terminal Menu The following Step/Action Tables and numbered tables provide informa- tion on setting up Example 3. Step Step 9-24 Instructions for Configuring the Ports for Example 3 Action Prior to setting up the Dial Plan, you must configure the Controller T1/PRI interfaces.

  • Page 119: Table 9-1. Network And Attached Equipment Provisioning

    Network PRI User Equipment NAME PORT OUTGOING ACCEPT # PRI-A Controller T1 $ - This port will Slot 0, Port 1 forward any call to the network. BRI-A Octal BRI 1)888-01[0,1]X BRI-B Slot 1, BRI-C Port 1,2,3 Allows calls to 888-0100 to 888-0119 2)888-0120 61200266L1-1...

  • Page 120: Table 9-3. User Terminations

    Chapter 9. Dial Plan Terminal Menu NAME PORT INCOMING ACCEPT # BRI-D Octal BRI 888-1001 (D); BRI-E Slot 1, 888-1002 (E); BRI-F Ports 4-5,6 888-1003 (F) PRI-B Controller T1 888-1010 Slot 0, This forms a hunt Port 2 group. T1-A Slot 2, 821-8XXX Port 1...
  • Page 121 Step Step Step After completing the network entries, the Network connection map appears as shown in Figure 9-6. 61200266L1-1 Setting PRI A Global Param (Continued) Action Back out of the connection to the index number column by pressing ESC on the keyboard. Insert three more connections into the list for the BRI lines by typing the letter I three times.

  • Page 122: Figure 9-6. Completed Network Map

    Chapter 9. Dial Plan Terminal Menu Step When you complete the User Term Dial Plan, it appears as shown in Figure 9-7. 9-28 Figure 9-6. Completed Network Map Setting User Term Connections Action Navigate to User Term. Enter connections for BRI D,E, and F in the same manner as BRI A, B, and C: use the copy (C) and paste (P) commands to enter the appropriate Out#Accept and Out#Reject numbers.

  • Page 123: Figure 9-7. Completed User Map

    Chapter 9. Dial Plan Terminal Menu Figure 9-7. Completed User Map A connection is not actually made (available) until you press Esc to move the cursor to the index number or move the cursor onto another connection line. PLUS 61200266L1-1 ATLAS 810 User Manual 9-29...
  • Page 124 Chapter 9. Dial Plan Terminal Menu PLUS 9-30 ATLAS 810 User Manual 61200266L1-1...

  • Page 125: Overview

    Updating Firmware Chapter 10 OVERVIEW To provide feature enhancements in the future, ATLAS 810 firmware updating by field personnel. Two transfer methods are available for use in updating any modules that contain Flash memory, including the ATLAS 810 ATLAS 810 fer method is via the ATLAS built-in Ethernet port using TFTP (Trivial File Transfer Protocol).

  • Page 126: Chapter 10 Updating Firmware

    ATLAS 810 do not know the password. • you must obtain the appropriate update file for the particular module from ADTRAN Technical Support at (888) 4ADTRAN (423-8726). • you may want to review Update Firmware on page 6-16. Step 10-2 PLUS .

  • Page 127: Figure 10-1. Update Firmware Menu Interface

    Also, when specifying the filename, ensure that the file transferred is the one provided by ADTRAN; otherwise, the update will not complete successfully.) Because XMODEM data is being transferred in-band through the menu interface, the VT-100 menus of ATLAS will be inoperable from the Chain In port.

  • Page 128: Tftp Firmware Updates

    ADTRAN Technical Support at (888) 4ADTRAN (423-8726). • you must copy the update file provided by ADTRAN to a network serv- er that supports TFTP Server requests. Record both the IP address of the server and the full path location of the update file to be downloaded.

  • Page 129: Table 10-1. Tftp Upload Messages

    If an error occurred during the update process, Previous Update Status displays the appropriate error message. In this case, return to step 3 and at- tempt the update process again. If the same error occurs, contact ADTRAN Technical Support. Message...

  • Page 130: Figure 10-2. Update Firmware Menu Interface

    Chapter 10. Updating Firmware Figure 10-2. Update Firmware Menu Interface PLUS 10-6 ATLAS 810 User Manual 61200266L1-1...

  • Page 131: Chapter 11 Snmp Management

    SNMP Management Chapter 11 SNMP As local area network (LAN) environments became standardized over the past ten years, multivendor equipment grew with competition. It became necessary to manage various vendor equipment from a single control con- sole. Thus, Simple Network Management Protocol (SNMP) emerged as the standard for managing commercial TCP/IP networks.

  • Page 132: Snmp Traps

    Chapter 11. SNMP Management SNMP TRAPS An SNMP trap is a message sent by a network device, such as the ATLAS 810 Trap Destination List A trap destination list contains information about sites designated to receive SNMP traps. You can configure this list via a Telnet session or the VT-100 terminal menu.

  • Page 133: Filtering (Disabling) Traps

    Filtering (Disabling) Traps You can disable trap generating events in three ways: Disable Trap Transmission. From the terminal menu, select SNMP and set Trap Transmission to DISABLED. Define trap thresholds to disable specific trap events. Refer to the ATLAS MIB in System Event Logging on page A-1 for a description of each trap event supported by the ATLAS.

  • Page 134: Ds1 Traps

    DS1 Traps ATLAS supports RFC1406, the DS1 standard MIB, as well as the ADTRAN DS1 MIB, an extension to RFC1406. The ADTRAN DS1 group lets you send traps for DS1 Alarm Failures and Performance Threshold Crossing Alerts. The DS1 Alarm Table, defined in the ADTRAN DS1 extension MIB, contains entries that enable the status bits to send an Alarm Trap message.

  • Page 135: Table 11-4. Ds1 Current Alert Snmp Traps

    ber of the trap destination list when accumulated error statistics exceed these threshold values. Table 11-4 describes the alert traps supported by ATLAS 810 Current Alert adATLAS800CurrentES adATLAS800CurrentSES adATLAS800CurrentSEFS adATLAS800CurrentUAS adATLAS800CurrentCSS adATLAS800CurrentLES adATLAS800CurrentCV When one of the Current Alert thresholds is exceeded, the corresponding event bit is set to 1 in the adDS1CurrentAlert variable in the DS1 alert table.

  • Page 136: Table 11-5. Total Alert Traps

    Chapter 11. SNMP Management Total Alert Severity adATLAS800TotalES Warning The total interval errored second threshold has been adATLAS800TotalSES Warning The total interval severely errored second threshold has adATLAS800TotalSEFS Warning The total interval severely errored framing second threshold adATLAS800TotalUAS Major adATLAS800TotalCSS Warning The total interval controlled slip second threshold has been adATLAS800TotalPCV Warning The total interval path code violations has been exceeded.

  • Page 137: Chapter 12 Adtran Utilities

    ADTRAN Utilities Chapter 12 OVERVIEW ADTRAN delivers several PC software utilities along with the ATLAS 810 with your shipment. They also include MIB files (located in the MIB directory). The utilities make interfacing with the terminal menu and transferring configuration files to and from TFTP Servers easier. The utilities all run on Microsoft Windows 3.1 or higher.

  • Page 138: Syslog Gui

    Chapter 12. ADTRAN Utilities SysLog GUI Figure 12-1 on page 12-2 shows the SysLog Host GUI. The conventional Menu Bar is described below beginning on page 12-3 (see also Figure 12-2). Other features are described here. Monitor The Monitor feature allows all SysLog messages to be pre-filtered by Sys- tem Name, Source, Slot and Port before displaying these messages to the user and logging the message to the pre-designated monitor log file.

  • Page 139: Menu Bar

    Priority Level Clear Red Events Alert Action Contents IP Status About SysLog Figure 12-2. SysLog Menu Tree for the Menu Bar PLUS ATLAS 810 User Manual Chapter 12. ADTRAN Utilities Critical Major Minor Warning Normal Info Popup File Size 12-3...

  • Page 140: Log Files

    Chapter 12. ADTRAN Utilities LOG FILES > Erases log files, defines Red events, sets priorities and action to be taken when an event occurs, and clears Red events. (See Define RED Events on page 12-4.) » Erase Log Files The SysLog utility, by default, stores all messages of a certain priority in a specified local log file or facility.

  • Page 141: Figure 12-3. Telnet Menu Tree

    Telnet session, refer to Using The Terminal Menu on Host Name Port Edit Entry Add New Delete Connect Background Bold Text Start Cfg Capture Express Feature Only Stop Cfg Capture Figure 12-3. Telnet Menu Tree PLUS ATLAS 810 User Manual Chapter 12. ADTRAN Utilities 12-5...

  • Page 142: Session Menu

    Chapter 12. ADTRAN Utilities SESSION > Click on Session to open the Telnet session. MENU » Connect Opens dialog box for setting Host Name and Port parameters for a Telnet session. Also lets you Edit Entry, Add New entry, and Delete stored entries.

  • Page 143: Transfer Cfg

    This option is helpful when debugging. HELP MENU > Provides on-line help for using the ADTRAN Utilities. » Contents Opens the on-line help. » IP Status Displays the local port address and the status of the connection.

  • Page 144: Vt-100 Utility

    Chapter 12. ADTRAN Utilities VT-100 UTILITY Use the VT-100 to configure an ATLAS 810 to a PC. The VT-100 display is almost identical to the Telnet display. For a detailed description of how to work with the Telnet program, refer to Navigating the Terminal Menu on page 5-1, and for a detailed description of the VT-100 interface, see VT-100 Utility on page 12-8.

  • Page 145: Edit Menu

    Identical to the Telnet Capture Menu (see Capture Menu on page 12-7). MENU HELP MENU > Provides on-line help and information about the version number. » Contents Opens on-line help. » About Displays version and owner information. 61200266L1-1 PLUS ATLAS 810 User Manual Chapter 12. ADTRAN Utilities 12-9...

  • Page 146: Tftp Server

    Chapter 12. ADTRAN Utilities TFTP SERVER The TFTP Server utility transfers ATLAS 810 from a TFTP Server. You can install this program on a PC running any ver- sion of Microsoft Windows. The configuration of an ATLAS 810 saved offline as a backup file. The saved file may also be used to send the...

  • Page 147: Colors

    The unlabeled field in the center of the screen displays prompts about the status of active transfers, such as bytes transferred and re- ceived. 61200266L1-1 PLUS unit’s transferred configuration to allow sending identical PLUS ATLAS 810 User Manual Chapter 12. ADTRAN Utilities 12-11...

  • Page 148: Status Field

    Saving the Current Configuration to a TFTP Server Before trying to save a configuration, ensure that the TFTP Server is running. If you are using the ADTRAN TFTP Server program, the server automatical- ly enables when you start the program. Also, please note the following: •...

  • Page 149: Successful Transfer

    The Previous Transfer Status field indicates success or failure of the trans- fer. If successful, the field reads Transfer Status field displays er. (For the ADTRAN TFTP Server, it is stored in the installation directory or the directory you specified.) Unsuccessful Transfer There are various reasons why a configuration download may fail.
  • Page 150 Select the System Utility menu, then the Config Transfer menu. Set the TFTP Server IP Address to the IP address of the machine running the TFTP Server program. (If you are using the ADTRAN TFTP Server, the IP address displays in the Status field.) Change the TFTP Server filename to the filename of a previously saved configuration you wish to load.

  • Page 151: Appendix A System Event Logging

    System Event Logging Appendix A This appendix describes the entries that may be logged by the system event log. Of particular impor- tance is the log event’s Category – this is the minimum severity level that must be set in order that the event be logged.

  • Page 152: Table A-1. System Event

    Appendix A. System Event Logging Event ATLAS configuration file loaded into the system and activated Console login failure Internal system temperature has returned to normal Internal system temperature is too high Module found Module removed or not responding Primary power supply is present but is not operating properly SNMP authentication failure System cold start...

  • Page 153: Table A-3. Nx 56/64 Events

    Event 511 Test Pattern Activated 511 Test Pattern Deactivated Bilateral Loopback Activated Bilateral Loopback Deactivated Clock Slip Alarm Active Clock Slip Alarm Cleared CTS Asserted CTS Dropped DCD Asserted DCD Dropped DTR Asserted DTR Dropped Excessive Zeros condition cleared Excessive Zeros from DTE External Clock Alarm External Clock Alarm Cleared Pll Alarm Active...

  • Page 154: Table A-4. Time Events

    Appendix A. System Event Logging Event Blue Alarm Cleared Blue Alarm Set Current T1 Controlled Slip Seconds Threshold Exceeded Warning Current T1 Errored Seconds Threshold Exceeded Current T1 Line Code Violations Threshold Exceeded Current T1 Line Errored Seconds Threshold Exceeded Current T1 Path Code Violations Threshold Exceeded Current T1 Severely Errored Framing Seconds Threshold Exceeded...

  • Page 155: Table A-5. Ethernet Events

    Event Tx Blue Alarm Set Tx Yellow Alarm Cleared Tx Yellow Alarm Set Yellow Alarm Cleared Yellow Alarm Set Event Not enough memory for Ethernet driver Event BRI LT configuration successful BRI NT configuration successful Normal Call busy Call busy Call cleared Call connected Call disconnected...
  • Page 156 Appendix A. System Event Logging Event Incorrectly formatted IE ISDN line released No B channels for call No BRI resources available No Matching SPID found No Matching SPID found No PRI resources available PRI CO configuration successful Normal PRI CPE configuration successful SPID Failed SPID Negotiation failed...

  • Page 157: Table A-7. Isdn Cause Code Events

    61200266L1-1 Appendix A. System Event Logging Table A-7. ISDN Cause Code Events Cause Code Event ACCESS_INFO_DISCARDED BAD_INFO_ELEM BEAR_CAP_NOT_AVAIL CALL_REJECTED CAP_NOT_IMPLEMENTED CHAN_DOES_NOT_EXIST CHAN_NOT_IMPLEMENTED CHANNEL_UNACCEPTABLE DEST_OUT_OF_ORDER FACILITY_NOT_IMPLEMENTED FACILITY_NOT_SUBSCRIBED FACILITY_REJECTED INCOMING_CALL_BARRED INCOMPATIBLE_DEST INTERWORKING_UNSPEC INVALID_CALL_REF INVALID_ELEM_CONTENTS INVALID_MSG_UNSPEC INVALID_NUMBER_FORMAT MANDATORY_IE_LEN_ERR MANDATORY_IE_MISSING NETWORK_CONGESTION NETWORK_OUT_OF_ORDER NO_CIRCUIT_AVAILABLE NO_ROUTE NO_USER_RESPONDING NONEXISTENT_MSG NORMAL_CLEARING...
  • Page 158 Appendix A. System Event Logging CAUSE CODE LOG ENTRIES Cause Code IEs that are non-Q.931 (i.e., the Coding Standard field is not 0) are logged with the following format: <message> : <coding standard> code <cause code> The coding standard field is one of the following: Reserved, National, or Local.

  • Page 159: Table A-8. Cause Code Log Entry Location Designations

    ISDN Layer 2 (LAPD) Message a. Provides a hex dump of the entire LAPD frame. Event ISDN Call Control Messages Information Host>>CC <tag><call ID> <message> ISDN Call Control Messages Information CC>>Host <tag><call ID> <message> ISDN Information Element 61200266L1-1 Table A-8. Cause Code Log Entry Location Designations Code Location IN0TL...
  • Page 160 Appendix A. System Event Logging PLUS A-10 ATLAS 810 User Manual 61200266L1-1...

  • Page 161: Appendix B Troubleshooting

    Troubleshooting Appendix B Modules seated improperly, module failure Remove all modules and cycle power to the unit. If self test still fails, call Technical Support and report the results. If the self test now passes, re-in- sert modules one at a time, running the self test after installing each mod- ule.
  • Page 162 Appendix B. Troubleshooting Misconfiguration, improper cabling • Verify that the T1 signal is being received. If not, check that the cabling is correct. • Verify that the T1 is being received without errors. If not, double-check that framing and coding are set properly. •...

  • Page 163: Appendix C Warranty And Technical Support Information

    Support Information WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within five years from the date of shipment if the product does not meet its published specifications or if it fails while in service. For detailed warranty, repair, and return information refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure.
  • Page 164 Appendix C. Warranty and Technical Support Information Repair and Return If ADTRAN Technical Support determines that a repair is needed, Technical Support will coordinate with the Customer and Product Service (CAPS) de- partment to issue an RMA number. For information regarding equipment...

  • Page 165: Appendix D Acronyms And Abbreviations

    Acronyms and Abbreviations Appendix D alternate mark inversion automatic number identification B8ZS bipolar eight zero substitution Basic Rate ISDN bits per second customer premise equipment channel service unit Clear to send DACS Digital Access Cross-Connect System data communications equipment DNIS dialed number identification service digital service, level 0 (64 kbps) data service unit...
  • Page 166 Appendix D. Acronyms and Abbreviations SNMP simple network management protocol robbed bit signaling TCP/IP Transmission Control Protocol/Internet Protocol time division multiplexing TFTP Trivial File Transfer Protocol terminal service unit wide area network PLUS ATLAS 810 User Manual 61200266L1-1...

  • Page 167: Appendix E Glossary

    Glossary Appendix E 10BaseT Ethernet connection The ATLAS 800 RJ-48C port that provides Ethernet LAN connection for TFTP, SNMP, and Telnet. alternate mark inversion. A Layer 1 line code used in a T1 carrier. Zeros are transmitted as zero volts, and ones are transmitted as pulses that alternate polarity.
  • Page 168 Appendix E. Glossary Bits per second. A measure of the speed of data communications. byte Eight bits of information composed of zeros or ones, one of which may include a parity bit. Basic Rate ISDN. An ISDN service that offers two bearer (B) channels. One channel (64 kbps) is used for data transfer and as a data-link.
  • Page 169 Appendix E. Glossary DNIS Dialed Number Identification Service. Service provided by a telephone company that allows the caller to see what number has been dialed. Digital signal (or service) having a transmission rate of 64 kbps intended to carry one voice channel (a phone call).
  • Page 170 Appendix E. Glossary kbps Kilobits per second. 1,000 bits per second. local area network. Group of computers and peripheral devices connected by a communications chan- nel, limited by distance. liquid crystal display. Alphanumeric characters that appear in a display area as a result of light reflect- ing off a special crystalline substance.
  • Page 171 Octal BRI/U Module PLUS One of the ATLAS 810 option modules. The Octal BRI/U Module provides eight basic rate ISDN U interfaces, each capable of operating in NT or LT mode. option modules Any optional, hot-swappable module that can be added to the ATLAS 800 system for a variety of applications.
  • Page 172 A direct line between two telephone switching centers. terminal service unit. T-Watch PRO The ADTRAN Microsoft Widows-based management software program designed to control TSU units from a remote PC. It also provides limited control over the configuration of the ATLAS 800 using a graphical user interface.
  • Page 173 Appendix E. Glossary XMODEM An error-correcting file transfer, data transmission protocol used to transmit files between PCs. The XMODEM protocol sends information in 128 byte blocks of data. Some sums (check sums) are done on each block and the result is sent along with the block. If the result does not check out at the other end, the computer at the other end sends a request (a NAK - negative acknowledgment) to retransmit that block again).
  • Page 174 Appendix E. Glossary PLUS ATLAS 810 User Manual 61200266L1-1...
  • Page 175 8-2 time 8-5 add password 6-13 address ADLP 6-8 ADLP address 6-8 ADTRAN utilities 12-1 ADTRAN data link layer protocol address 6-8 alarm blue 7-4 status 7-4 system 6-5 yellow 7-4, 7-6 yellow auto TX 7-6 alarm key 4-4...
  • Page 176 6-8 ethernet port name 6-8 Index-2 flow control 6-9 IP address 6-8 module slots 7-2 subnet mask 6-8 configuring ATLAS 810 PLUS 6-1 configuring Syslog 6-12 connect Telnet menu 12-6 connection activate 8-2 control in / chain in 2-5...
  • Page 177 description 1-4 data 56 kbps accept 9-7 56 kpbs reject 9-8 64 kbps accept 9-4, 9-7 reject 9-5, 9-8 data tables 6-6 configuring 6-6 date current 6-12 restart schedule 6-17 restart system 6-17 set 6-3 daylight savings 6-12 data carrier detect 6-6 D-chan 7-4 dedicated and switched connection maps description 1-3...
  • Page 178 Index enbl day 8-5 end of number timeout 9-8 enter dedicated map connections 8-2 entry edit (Telnet utility) 12-6 erase event log 6-5 selftest log 6-22 errored seconds 7-5 ES 7-5 ESF 2-8 ethernet 10BaseT connection 2-6 connection 2-9 pinout 2-6 port 6-5, 6-8 configure 6-8 event...

  • Page 179: Local Echo

    6-9 insert dedicated map connection 8-3 insert password 6-13 Installation 2-1 installed memory 6-3 installing ATLAS 810 PLUS 2-1 modules 2-9 interface configuration 9-8 Introduction 1-1 status (Telnet utility) 12-7 IP address configure 6-8 TFTP server 6-17, 6-19...
  • Page 180 Index system utility 6-16 method signaling 9-14 modem initialize 6-9 modem initialization string 6-9 module configuration 7-6 menu 7-2 slot 7-2 state 7-3 type 7-2 update firmware 6-17 module online LED 4-4 module settings 6-1 module slot update firmware 6-16 module slots preconfigure 7-2 module status LED 4-4...
  • Page 181 out#rej 9-5, 9-7 outgoing caller ID 9-12, 9-17 outgoing number conversion 9-11 outgoing#accept 9-3 overrun errors 6-7 overview product 1-1 packing list 2-1 panel rear 2-3 parameters global 9-8 part num 7-4 password access 6-13, 6-14 add new 6-13 change 6-13 default 6-13 define 6-13 delete 6-13...
  • Page 182 Index network termination/PRI 9-10 network termination/RBS 9-13 user termination/PRI 9-16 user termination/RBS 9-18 Quad T1/PRI 9-13, 9-18 RCV 7-5 real time clock 6-12 rear panel 2-3 reboot system 6-23 receive level 7-4 red alarm 7-4 red CSU LED 4-4 red module status LED 4-4 refresh screen 12-9 reject numbers 9-5, 9-7 remote access...
  • Page 183 privileges 6-9 solid green system LED 4-4 solid red system LED 4-4 sort to/from 8-2 source ID 9-3, 9-6, 9-12, 9-15, 9-17, 9-19 speech accept 9-4, 9-7 reject 9-5, 9-8 SPID list 9-20 Octal BRI 9-21 start ground 9-18 loop 9-18 start telnet session 3-3 startup mode mode...
  • Page 184 Index moving around in 5-2 navigating with the keyboard keys 5-3 navigation help 5-3 operation 5-1, 9-1 paste items from clipboard 5-5 port status 5-3 refresh the screen 5-4 restore factory default settings 5-5 right pane notation 5-2 structure 5-1, 9-1 Sys 5-3 system time 5-3 tool tip 5-3...
  • Page 185 Octal BRI 9-21 Quad T1/PRI 9-16, 9-18 terminations 9-5 users logged into system, number of 6-14 using operation keys 4-4 using the front panel 4-1 utilities 12-1 utility TFTP server 12-10 VT 100 12-8 video conferencing setup with dial plan 9-23 view selftest log 6-21 view error log 6-4...

  • Page 186: Index

    Index PLUS Index-12 ATLAS 810 User Manual 61200266L1-1...
  • Page 187 Technical Support Repair and Return If ADTRAN Technical Support determines that a repair is needed, Technical Support will coordinate with the Custom and Product Service (CAPS) department to issue an RMA number. For information regarding equipment currently in house or possible fees associ-...

Table of Contents